Nerf N Strike Elite Alpha Trooper Cs 12 Trigger Spring Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 25 minutes

Sections

Trigger Spring
6 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

BackNerf N-Strike Elite Alpha Trooper CS-12
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Notes Before Starting

There are many screws of varying lengths involved in the disassembling of this device. It is important to keep track which screws correspond to which holes. This will help ensure proper reassembly.
Be sure that the rifle is discharged and unloaded before starting disassembly.

There are many screws of varying lengths involved in the disassembling of this device. It is important to keep track which screws correspond to which holes. This will help ensure proper reassembly.

Be sure that the rifle is discharged and unloaded before starting disassembly.

1024

Step 2

              Rear Cap Removal

Looking at the rear of the rifle, remove the two 10 mm phillips screws holding the orange cap to the butt of the rifle.
Pull off the orange cap.

Looking at the rear of the rifle, remove the two 10 mm phillips screws holding the orange cap to the butt of the rifle.

Pull off the orange cap.

Step 3

              Slide Removal

With the rifle barrel pointing left, remove the two 8 mm phillips screws holding the slide mechanism together.
Remove the three 10 mm phillips screws from the bottom of the slide mechanism.
Remove the two halves of the slide mechanism.
Make sure to keep track of which screws correspond to which holes.

With the rifle barrel pointing left, remove the two 8 mm phillips screws holding the slide mechanism together.

Remove the three 10 mm phillips screws from the bottom of the slide mechanism.

Remove the two halves of the slide mechanism.

Make sure to keep track of which screws correspond to which holes.

Step 4

Again with the rifle barrel pointing left, remove the fourteen 10 mm phillips screws from the main body of the rifle.
Remove the two 5mm phillips screws from the main body.
Remove the two 8 mm phillips screws from the main body.
Screws are varying lengths, make sure to keep track of which screws correspond to which holes.

Again with the rifle barrel pointing left, remove the fourteen 10 mm phillips screws from the main body of the rifle.

Remove the two 5mm phillips screws from the main body.

Remove the two 8 mm phillips screws from the main body.

Screws are varying lengths, make sure to keep track of which screws correspond to which holes.

Step 5

Pull the two halves of the rifle apart.
Be careful of the spring at the rear end of the rifle. It may come flying out.
If you have difficulty pulling the two halves apart, use a spudger gently pry the edges of the body apart.
Also be careful of small parts when opening the gun, they may be easy to lose.
Remove the access gate and barrel cover.

Pull the two halves of the rifle apart.

Be careful of the spring at the rear end of the rifle. It may come flying out.

If you have difficulty pulling the two halves apart, use a spudger gently pry the edges of the body apart.

Also be careful of small parts when opening the gun, they may be easy to lose.

Remove the access gate and barrel cover.

Step 6

              Trigger Removal

Remove the single 8mm phillips screw holding the trigger mechanism is place.
Remove the trigger mechanism.
Remove the small spring from the rear of the mechanism and replace it with a new spring.

Remove the single 8mm phillips screw holding the trigger mechanism is place.

Remove the trigger mechanism.

Remove the small spring from the rear of the mechanism and replace it with a new spring.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors

                    Henrique Chan

Member since: 01/24/2014

303 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 10-35, Maness Winter 2014                        

                                                  Member of Cal Poly, Team 10-35, Maness Winter 2014 



                    CPSU-MANESS-W14S10G35                     


                                            4 Members                     


                                            5 Guides authored

Slice and Dice#

Introduction#

What you need#

Team#

Slice and Dice

Introduction

What you need

Team