Difficulty
Moderate
Steps
10
Time Required
35 minutes
Sections
1
- Dart Tooth
- 10 steps
Flags
0
BackNerf N-Strike Deploy CS-6
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Dart Tooth
- Before releasing the device in Stealth mode, take out hidden screws as shown
- Extend the device in Stealth Mode by pressing the button found on the handle.
Before releasing the device in Stealth mode, take out hidden screws as shown
Extend the device in Stealth Mode by pressing the button found on the handle.
1024
Step 2
- Take out the screws from the pump.
- Proceed to take out the other screws from the device to take off the cover.
- For the pump, the screw’s length extends out to 1.9 cm. The majority size of the screws extend out to 1.3 cm.
Take out the screws from the pump.
Proceed to take out the other screws from the device to take off the cover.
For the pump, the screw’s length extends out to 1.9 cm. The majority size of the screws extend out to 1.3 cm.
Step 3
- Once the screws are out, you are able to take the cover piece off.
- Proceed to remove the screws
- Taking off those screws are vital in replacing the dart tooth.
Once the screws are out, you are able to take the cover piece off.
Proceed to remove the screws
Taking off those screws are vital in replacing the dart tooth.
Step 4
- Carefully place cover piece above the device.
Carefully place cover piece above the device.
Step 5
- Unscrew as shown to aid in the replacement.
Unscrew as shown to aid in the replacement.
Step 6
- To take out the dart tooth, push the spring to the left.
- The dart tooth should pop out with ease.
To take out the dart tooth, push the spring to the left.
The dart tooth should pop out with ease.
Step 7
- Once pulled away from the device, take off the orange piece connected to the darth tooth
- The piece can be identified with the spring.
Once pulled away from the device, take off the orange piece connected to the darth tooth
The piece can be identified with the spring.
Step 8
- You should now be able to pull apart the dart tooth from the device.
- The piece that has been pulled away will have a type of lubrication. If this piece requires replacement, it will slide on with ease.
You should now be able to pull apart the dart tooth from the device.
The piece that has been pulled away will have a type of lubrication. If this piece requires replacement, it will slide on with ease.
Step 9
- Make any adjustment to the dart tooth as seen. May be pulled either up or down.
- Place in the replacing piece in order to fix the darth tooth
Make any adjustment to the dart tooth as seen. May be pulled either up or down.
Place in the replacing piece in order to fix the darth tooth
Step 10
- Place back on the orange piece with the spring to its original spot on the dart tooth.
- While setting in the dart tooth back into place, the small spring on the yellow piece must be placed in its compartment as shown.
- Place back cover pieces in order to secure the screws back into place.
Place back on the orange piece with the spring to its original spot on the dart tooth.
While setting in the dart tooth back into place, the small spring on the yellow piece must be placed in its compartment as shown.
Place back cover pieces in order to secure the screws back into place.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Alec Hernandez
Member since: 09/28/2016
126 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
Eastern Washington University, Team 2-5, Mathisen Fall 2016
Member of Eastern Washington University, Team 2-5, Mathisen Fall 2016
EWU-MATHISEN-F16S2G5
4 Members
4 Guides authored