Difficulty

Moderate

Steps

12

Time Required

                          15 - 30 minutes

Sections

1

  • Spring
  • 12 steps

Flags

4

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Scenic Route

This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

  • BackNERF Doomlands 2169 Lawbringer Blaster

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Spring
  • Remove sixteen screws from the outer case.
  • Remove the outer case from the rest of the device.

Remove sixteen screws from the outer case.

Remove the outer case from the rest of the device.

1024

Step 2

  • Remove the three screws attached to the trigger mechanism of the gun.
  • Potential for device damage: Be careful when removing the rotating cartridge from the case, as the fulcrum attaching it to the trigger mechanism will fall out!

Remove the three screws attached to the trigger mechanism of the gun.

Potential for device damage: Be careful when removing the rotating cartridge from the case, as the fulcrum attaching it to the trigger mechanism will fall out!

Step 3

  • Remove the exterior spring from the sliding mechanism and rotate the gun to the opposite side.

Remove the exterior spring from the sliding mechanism and rotate the gun to the opposite side.

Step 4

  • Remove the three screws holding the trigger plate in place, then remove the plate carefully.

Remove the three screws holding the trigger plate in place, then remove the plate carefully.

Step 5

  • Remove the spring and trigger mechanism from the gun and set aside.

Remove the spring and trigger mechanism from the gun and set aside.

Step 6

  • Carefully slide out the big spring and fit in your replacement (the thin-coil end is coiled around the orange plastic).
  • Potential for device damage: This is where the spring load mechanism is located. Be cautious not to damage. If the spring separates from the gun, reattach it using a screwdriver end.

Carefully slide out the big spring and fit in your replacement (the thin-coil end is coiled around the orange plastic).

Potential for device damage: This is where the spring load mechanism is located. Be cautious not to damage. If the spring separates from the gun, reattach it using a screwdriver end.

Step 7

  • Keep tension on the spring and begin sliding the new coil spring into the trigger mechanism.
  • Make sure the orange slide is above the spring. A second set of hands would be useful during this step.

Keep tension on the spring and begin sliding the new coil spring into the trigger mechanism.

Make sure the orange slide is above the spring. A second set of hands would be useful during this step.

Step 8

  • Reconnect the spring to the orange slider and connect the orange slider to the grey hook.

Reconnect the spring to the orange slider and connect the orange slider to the grey hook.

Step 9

  • Slide the orange supporting piece into the crevice below the air chamber.

Slide the orange supporting piece into the crevice below the air chamber.

Step 10

  • Slide the rotating cartridge back into place.

Slide the rotating cartridge back into place.

Step 11

  • Carefully reassemble the NERF Lawbringer in the same order you took it apart. Carefully reattach the three screws that seal the air chamber.

Carefully reassemble the NERF Lawbringer in the same order you took it apart. Carefully reattach the three screws that seal the air chamber.

Step 12

  • Reattach the other plastic half of the gun. Tighten the screws and you’re done.

Reattach the other plastic half of the gun. Tighten the screws and you’re done.

Cancel: I did not complete this guide.

Author

                                      with 8 other contributors 


                    Georgia Slack

Member since: 10/13/2016

113 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       University of Maine, Team 1-5, Diaz Fall 2016                        

                                                  Member of University of Maine, Team 1-5, Diaz Fall 2016 



                    UMAINE-DIAZ-F16S1G5                     


                                            2 Members                     


                                            1 Guide authored