Difficulty
Moderate
Steps
10
Time Required
45 minutes
Sections
1
- Catch Spring
- 10 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackNERF Doomlands 2169 Lawbringer Blaster
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Catch Spring
- Locate and remove all 14 screws of the outer case and gently remove it avoiding any damage.
Locate and remove all 14 screws of the outer case and gently remove it avoiding any damage.
1024
Step 2
- Remove the three screws attached to the trigger mechanism of the gun.
- Be careful when removing the rotating cartridge from the case, as the fulcrum attaching it to the trigger mechanism will fall out.
Remove the three screws attached to the trigger mechanism of the gun.
Be careful when removing the rotating cartridge from the case, as the fulcrum attaching it to the trigger mechanism will fall out.
Step 3
- Remove the exterior spring from the sliding mechanism and re-position the gun on its opposite side.
Remove the exterior spring from the sliding mechanism and re-position the gun on its opposite side.
Step 4
- Remove the three screws holding the trigger plate in place, then remove the plate carefully.
Remove the three screws holding the trigger plate in place, then remove the plate carefully.
Step 5
- Remove the spring and trigger mechanism from the gun, and set aside.
Remove the spring and trigger mechanism from the gun, and set aside.
Step 6
- This is where the spring load mechanism is located, be cautious not to damage. If the spring separates from the gun, reattach it using a screwdriver end.
- Carefully slide out the big spring and fit in your replacement (thin-coil end coiled around the orange plastic)
This is where the spring load mechanism is located, be cautious not to damage. If the spring separates from the gun, reattach it using a screwdriver end.
Carefully slide out the big spring and fit in your replacement (thin-coil end coiled around the orange plastic)
Step 7
- A second set of hands would be useful during this step. Make sure the orange slide is above the spring.
- Keep tension on the spring and begin sliding the new coil spring into the trigger mechanism.
A second set of hands would be useful during this step. Make sure the orange slide is above the spring.
Keep tension on the spring and begin sliding the new coil spring into the trigger mechanism.
Step 8
- Reconnect the spring to the orange slider, and connect the orange slider to the grey hook.
Reconnect the spring to the orange slider, and connect the orange slider to the grey hook.
Step 9
- Slide the orange supporting piece into the crevice below the air chamber.
- Slide the rotating cartridge back into place
Slide the orange supporting piece into the crevice below the air chamber.
Slide the rotating cartridge back into place
Step 10
- Look to the beginning of this guide for help to reassemble this gun.
- Carefully reassemble the Nerf Law bringer in the same order you took it apart. Carefully reattach the 3 screws that seal the air chamber.
- Reattach the other plastic half of the gun. Tighten the screws and you’re done.
Look to the beginning of this guide for help to reassemble this gun.
Carefully reassemble the Nerf Law bringer in the same order you took it apart. Carefully reattach the 3 screws that seal the air chamber.
Reattach the other plastic half of the gun. Tighten the screws and you’re done.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 6 other contributors
Daniel Perriello
Member since: 11/04/2015
134 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
University of Maine, Team 1-4, Diaz Fall 2015
Member of University of Maine, Team 1-4, Diaz Fall 2015
UMAINE-DIAZ-F15S1G4
2 Members
1 Guide authored
