Difficulty
Difficult
Steps
20
Time Required
Suggest a time??
Sections
4
- Back Panel
- 4 steps
- Motherboard
- 11 steps
- Battery & LED screen
- 3 steps
- Audio PCB
- 2 steps
Flags
3
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
Better Introduction
Improve this guide by completing or revising its introduction.
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackNeo3DO
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Back Panel
- Turn the Neo3DO face down so that the logo is facing toward you.
- Insert the plastic opening tool between the metal frame and the plastic back panel, as shown.
Turn the Neo3DO face down so that the logo is facing toward you.
Insert the plastic opening tool between the metal frame and the plastic back panel, as shown.
1024
Step 2
- Gently pry the back panel upwards.
- Ensure the tool does not slip into the device and damage the internals.
Gently pry the back panel upwards.
Ensure the tool does not slip into the device and damage the internals.
Step 3
- Once the back panel has been pried away from the bottom and sides of the Neo3DO, lift the back panel up and away from the tablet.
Once the back panel has been pried away from the bottom and sides of the Neo3DO, lift the back panel up and away from the tablet.
Step 4
- When replacing the back panel, place the top edge of the back panel against the top edge of the Neo3DO, as shown.
- The top edge of the device is the edge closest to the camera. The top of the back panel is the side with the hole for the camera.
When replacing the back panel, place the top edge of the back panel against the top edge of the Neo3DO, as shown.
The top edge of the device is the edge closest to the camera. The top of the back panel is the side with the hole for the camera.
Step 5
Motherboard
- Remove all the tape attached to the motherboard.
Remove all the tape attached to the motherboard.
Step 6
- Pull out the black tabs using the plastic spudger.
- All sockets that require the same step are marked in the first photo.
Pull out the black tabs using the plastic spudger.
All sockets that require the same step are marked in the first photo.
Step 7
- Remove the wire belt from the socket.
Remove the wire belt from the socket.
Step 8
- Lift the black tab and then remove the wire belt.
Lift the black tab and then remove the wire belt.
Step 9
Step 10
- Grip the side of the tab and pull upwards to remove it from the socket.
- All sockets that require the same step are marked in the first photo.
- Gripping the wire belt and pulling upwards may cause damage, be sure to avoid it.
Grip the side of the tab and pull upwards to remove it from the socket.
Gripping the wire belt and pulling upwards may cause damage, be sure to avoid it.
Step 11
- Remove the screws using the J0 head screwdriver.
- All screws that require the same step are marked in the first photo.
Remove the screws using the J0 head screwdriver.
All screws that require the same step are marked in the first photo.
Step 12
- Grip the active(red) wire and apply the soldering tool until the solder is soft enough for the wire to be removed.
- Repeat the same process to remove the neutral(black) wire.
- All wires that require the same steps are marked in the first photo.
- The soldering tool is extremely hot, use with caution.
Grip the active(red) wire and apply the soldering tool until the solder is soft enough for the wire to be removed.
Repeat the same process to remove the neutral(black) wire.
All wires that require the same steps are marked in the first photo.
The soldering tool is extremely hot, use with caution.
Step 13
- Use the flat end of the plastic spudger to remove the motherboard and turn it underside-up.
Use the flat end of the plastic spudger to remove the motherboard and turn it underside-up.
Step 14
- Remove the plug from the motherboard socket.
Remove the plug from the motherboard socket.
Step 15
- Grip the wire and apply the soldering tool until the solder is soft enough for the wire to be removed.
- The soldering tool is extremely hot, use with caution.
Grip the wire and apply the soldering tool until the solder is soft enough for the wire to be removed.
Step 16
Battery & LED screen
- Remove the screws with a J000 screwdriver
- All screws that require the same step are marked in the first photo.
Remove the screws with a J000 screwdriver
Step 17
- Use the plastic removal tool to remove the plastic frame.
Use the plastic removal tool to remove the plastic frame.
Step 18
- Using the plastic removal tool, lift the LED screen from the battery side, and use the tweezers to help lift the LED screen upwards.
Using the plastic removal tool, lift the LED screen from the battery side, and use the tweezers to help lift the LED screen upwards.
Step 19
Audio PCB
- Remove the screws using the Philip’s PH000 screwdriver.
- All screws that require the same step are marked in the first photo.
Remove the screws using the Philip’s PH000 screwdriver.
Step 20
- Use the plastic removal tool to pry the audio PCB and pull away from the frame to remove it.
Use the plastic removal tool to pry the audio PCB and pull away from the frame to remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Daniel Evans
Member since: 09/26/2016
431 Reputation
4 Guides authored
Badges:
5
+2 more badges
Team
USF Tampa, Team 14-3, Eyestone Fall 2016
Member of USF Tampa, Team 14-3, Eyestone Fall 2016
USFT-EYESTONE-F16S14G3
3 Members
12 Guides authored
