Neato Botvac D75 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Battery
3 steps
Brushes
3 steps
LCD Screen
8 steps

Flags

BackNeato Botvac D75
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Also, please note that there may be dirt and debris that are knocked lose while disassembling your Botvac. Keeping a clean work area will prevent you from losing parts in the mess.

What you need

Step 1

              Battery

Use Phillips #1 screwdriver to unscrew the two bottom cover screws
Be careful, the screws are self-retained on the cover itself and does not come off the battery cover.

Use Phillips #1 screwdriver to unscrew the two bottom cover screws

Be careful, the screws are self-retained on the cover itself and does not come off the battery cover.

1024

Step 2

Lift battery cover out.

Lift battery cover out.

Step 3

Be careful when taking out the battery. Do not pull on the wires or battery trying to get the connector out.
The cord has prongs on it that are a little difficult to get out. Use a flathead screwdriver to press the release tab on the connector to remove it.

Be careful when taking out the battery. Do not pull on the wires or battery trying to get the connector out.

The cord has prongs on it that are a little difficult to get out. Use a flathead screwdriver to press the release tab on the connector to remove it.

Step 4

              Brushes

To remove the rotary brush simply grasp it firmly and pull it off.

To remove the rotary brush simply grasp it firmly and pull it off.

Step 5

Once you have everything out get the plastic opening tool and pry open the large black plastic piece.
With a little force it should come out.
The boxes show you were the clips are that hold this piece

Once you have everything out get the plastic opening tool and pry open the large black plastic piece.

With a little force it should come out.

The boxes show you were the clips are that hold this piece

Step 6

Once the black piece has been taken out, the brush just comes out easily.

Once the black piece has been taken out, the brush just comes out easily.

Step 7

              LCD Screen

Firmly grasp the back cover and pull away from the Botvac one side at a time.
Removing the cover will expose two 1.3mm T10 screws that must be removed to separate the cover halves.

Firmly grasp the back cover and pull away from the Botvac one side at a time.

Removing the cover will expose two 1.3mm T10 screws that must be removed to separate the cover halves.

Step 8

Remove these two 13mm T10 screws. You will need to use the extension in your tool set since they are deep in the casting.

Remove these two 13mm T10 screws. You will need to use the extension in your tool set since they are deep in the casting.

Step 9

Eight 13mm T10 screws on the underside of the Botvac hold the casing together. These screws are not self-retained so make sure that you don’t lose them in the disassembly process.

Eight 13mm T10 screws on the underside of the Botvac hold the casing together. These screws are not self-retained so make sure that you don’t lose them in the disassembly process.

Step 10

The screws pictured here on either side of the Botvac require the extension in your tool set to be removed.

The screws pictured here on either side of the Botvac require the extension in your tool set to be removed.

Step 11

On the back of the Botvac there are two retaining tabs that must be pressed to be released.
With the tabs released the top and bottom cover halves can be separated.

On the back of the Botvac there are two retaining tabs that must be pressed to be released.

With the tabs released the top and bottom cover halves can be separated.

Step 12

Carefully lift the top cover of the Botvac. On the right side of the Botvac is where you’ll find the LCD screen connector to the motherboard. Carefully pull on the connector to disconnect it from the motherboard.

Carefully lift the top cover of the Botvac. On the right side of the Botvac is where you’ll find the LCD screen connector to the motherboard. Carefully pull on the connector to disconnect it from the motherboard.

Step 13

There are two 0.5cm #1 Phillips screws holding the LCD screen to the top cover. Remove these screws to lift screen off the cover.

There are two 0.5cm #1 Phillips screws holding the LCD screen to the top cover. Remove these screws to lift screen off the cover.

Step 14

With the two screws removed you may lift the screen off the cover. Carefully remove the connector from the screen by pulling on the connector.

With the two screws removed you may lift the screen off the cover. Carefully remove the connector from the screen by pulling on the connector.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors

                    Juan Cornejo

Member since: 02/15/2017

597 Reputation

                                      5 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team S6-G5, Lacy Spring 2017                        

                                                  Member of USF Tampa, Team S6-G5, Lacy Spring 2017 



                    USFT-LACY-S17S6G5                     


                                            4 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team