Difficulty
Moderate
Steps
8
Time Required
30 minutes
Sections
3
- Rear Bumper
- 2 steps
- Top Face Panel
- 3 steps
- Laser
- 3 steps
Flags
0
BackNeato Botvac 80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Bumper
- Grab the rear bumper with both hands on either side.
Grab the rear bumper with both hands on either side.
1024
Step 2
- Pull the left and right sides away from the machine to unclip the bumper. This requires that you bend the plastic a little bit. Unclip one side a little bit and allow the prong to rest on the side of the machine. Then unclip the other side and pull off the bumper parallel to both sides
Pull the left and right sides away from the machine to unclip the bumper. This requires that you bend the plastic a little bit. Unclip one side a little bit and allow the prong to rest on the side of the machine. Then unclip the other side and pull off the bumper parallel to both sides
Step 3
Top Face Panel
- Looking from above, remove the two 11mm screws with a torx T10 screwdriver.
Looking from above, remove the two 11mm screws with a torx T10 screwdriver.
Step 4
- Begin by placing the robot on it’s back and removing the six 11m screws using a Torx T10 screwdriver.
Begin by placing the robot on it’s back and removing the six 11m screws using a Torx T10 screwdriver.
Step 5
- To remove the top, you must press in both of the clamps at the same time and push upwards.
- When removing the top, before you can completely take it off you must unplug the LCD power cable from the motherboard.
To remove the top, you must press in both of the clamps at the same time and push upwards.
When removing the top, before you can completely take it off you must unplug the LCD power cable from the motherboard.
Step 6
Laser
- Lift gently upon the top panel.
- Unplug the clip located on the right side before completely removing.
Lift gently upon the top panel.
Unplug the clip located on the right side before completely removing.
Step 7
- This black cap spins so may need a hand when unscrewing the screws.
- Locate and unscrew the four 12 mm screws located in the black cap with the phillips #00 screwdriver.
- Lift the black cap to reveal the laser.
This black cap spins so may need a hand when unscrewing the screws.
Locate and unscrew the four 12 mm screws located in the black cap with the phillips #00 screwdriver.
Lift the black cap to reveal the laser.
Step 8
- There are two loosely secured black blinders on both the laser and sensor.
- Gently pull back on the gold laser to remove it from the socket.
- Unplug the mini LCU clip by gently pulling up and remove the laser.
There are two loosely secured black blinders on both the laser and sensor.
Gently pull back on the gold laser to remove it from the socket.
Unplug the mini LCU clip by gently pulling up and remove the laser.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 3 other contributors
Brandon Blank
Member since: 02/02/2017
675 Reputation
5 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 17-5, Blackwell Spring 2017
Member of USF Tampa, Team 17-5, Blackwell Spring 2017
USFT-BLACKWELL-S17S17G5
3 Members
12 Guides authored
Evgany Vorona - Apr 15, 2018
Reply
lol. You don’t need to open it to replace the laser. The top is a clip on. Just pull it and remove 4 screws.
Nancy Butler - May 7, 2018
Reply
where do you buy the replacement laser?
Anthony Mainini - May 10, 2018
I too would like to know where he got a replacement laser.
Beverly Jurgensen - May 10, 2018
Reply
where do I buy a replacement laser?
Beverly Jurgensen
Where do I buy a replacement laser?
