Difficulty

Moderate

Steps

6

Time Required

                          25 - 30 minutes

Sections

1

  • Motherboard
  • 6 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackNCR 7606-1504-8801-A3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Motherboard
  • You will need the security key that came with the register to unlock the front panel.
  • There are two screws in the back to release the cover.

You will need the security key that came with the register to unlock the front panel.

There are two screws in the back to release the cover.

1024

Step 2

  • Unplug the two marked cables form the hard drive.
  • Press the button on the side of the register and lift until the latch disengages.

Unplug the two marked cables form the hard drive.

Press the button on the side of the register and lift until the latch disengages.

Step 3

  • Disconnect all cables that are coming from the power supply.
  • Be sure to check the normal 24 and 4 pin power supply cables. But also look around for any supporting components that require power.
  • Remove the power supply by pulling it towards yourself . (As is you are looking down at the device).

Disconnect all cables that are coming from the power supply.

Be sure to check the normal 24 and 4 pin power supply cables. But also look around for any supporting components that require power.

Remove the power supply by pulling it towards yourself . (As is you are looking down at the device).

Step 4

  • Unscrew the two face plate screws.
  • Remove the cables from the motherboard and pull the expansion board out.

Unscrew the two face plate screws.

Remove the cables from the motherboard and pull the expansion board out.

Step 5

  • Unscrew the 4 indicated screws from the heat sink and pull gently to remove
  • When replacing, put on a coat of thermal conductive gel before reattaching heat sink.

Unscrew the 4 indicated screws from the heat sink and pull gently to remove

When replacing, put on a coat of thermal conductive gel before reattaching heat sink.

Step 6

  • Remove the screw holding the motherboard in place.
  • Remove the motherboard and replace.

Remove the screw holding the motherboard in place.

Remove the motherboard and replace.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Devon Large

Member since: 01/31/2019

133 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       University of Advancing Technology, Team S1-G5, Beam Spring 2019                        

                                                  Member of University of Advancing Technology, Team S1-G5, Beam Spring 2019 



                    UAT-BEAM-S19S1G5                     


                                            3 Members                     


                                            1 Guide authored

Kobus Brisley - Oct 27, 2020

Reply

I have a ncr pocono d-nr6-d-021 v1.0 motherboard with which i am batteling to connect the front panel connectors onto the board. As this was a ATM board with connectors to a front panel i now use it as a PC DESKTOP .The motherboard has the following starting from the leftf audio -10 pins ,panel 1 - 10 pins missing pin 3j2 - 16 pins missing pin 11The connectors isPower led+ (green),power led- (white)reset switch (cream & white),Hdd Led, (yellow & white)HD audio, (black, dark blue, yellow, white, orange,green,purple, red) _____That is connectedPower switch (black & white),USb (red red white white green green black black). ______That is connected.Hope you can help me.Thanks.