Difficulty
Moderate
Steps
14
Time Required
3 minutes
Sections
5
- Rear panel
- 2 steps
- Battery
- 2 steps
- Charging port
- 2 steps
- Motherboard
- 5 steps
- Speakers
- 3 steps
Flags
0
BackNABI XD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear panel
- Use the plastic opening tool at the top left corner seam, then pry the corner apart.
Use the plastic opening tool at the top left corner seam, then pry the corner apart.
1024
Step 2
- Next slide the plastic opening tool across the sides of the Nabi. It will slowly open.
- There are small plastic clips that need to be release. Gently apply outwards pressure until the clips give.
- Go around the NABI XD and separate the rear panel from the device.
Next slide the plastic opening tool across the sides of the Nabi. It will slowly open.
There are small plastic clips that need to be release. Gently apply outwards pressure until the clips give.
Go around the NABI XD and separate the rear panel from the device.
Step 3
Battery
- Place your fingernails on both sides of the connector and pull it straight back away from the holder.
Place your fingernails on both sides of the connector and pull it straight back away from the holder.
Step 4
- Battery is glued to the base, lift carefully.
- To remove battery, lift the battery up from the motherboard.
Battery is glued to the base, lift carefully.
To remove battery, lift the battery up from the motherboard.
Step 5
Charging port
- Remove the two 4mm Phillips screws with the PH#0 screwdriver.
- Disconnect the left (L) speaker wire from the charging port by grabbing it on both sides with the tweezers and pulling straight back.
Remove the two 4mm Phillips screws with the PH#0 screwdriver.
Disconnect the left (L) speaker wire from the charging port by grabbing it on both sides with the tweezers and pulling straight back.
Step 6
- Use your fingernails or a spudger to flip up the small retaining flap, then pull the ribbon straight back to remove
- Lift the charging port from the NABI XD.
Use your fingernails or a spudger to flip up the small retaining flap, then pull the ribbon straight back to remove
Lift the charging port from the NABI XD.
Step 7
Motherboard
- To remove the marked ribbons, use your fingernails or a spudger to lift up small tab
- Use the Precision Tweezers to gently pull the ribbons straight out of the connectors.
- You need to remove 4 ribbons
To remove the marked ribbons, use your fingernails or a spudger to lift up small tab
Use the Precision Tweezers to gently pull the ribbons straight out of the connectors.
You need to remove 4 ribbons
Step 8
- Disconnect the camera by lifting the ribbon straight up. Also disconnect the remaining ribbon by lifting up gently.
- To disconnect antenna wire, use the tweezers to pry connector straight from the board.
Disconnect the camera by lifting the ribbon straight up. Also disconnect the remaining ribbon by lifting up gently.
To disconnect antenna wire, use the tweezers to pry connector straight from the board.
Step 9
- Disconnect the Right speaker by grabbing the wire head by its sides and pulling it back from the connector.
Disconnect the Right speaker by grabbing the wire head by its sides and pulling it back from the connector.
Step 10
- Remove the four 4mm Phillips screws with the PH#0 screwdriver.
Remove the four 4mm Phillips screws with the PH#0 screwdriver.
Step 11
- Lift the motherboard up away from the Nabi XD.
Lift the motherboard up away from the Nabi XD.
Step 12
Speakers
- Right (R) speaker removal:
- Remove one 4mm Phillips screw.
- Use the metal spudger to separate the speaker from the frame.
- The speaker is glued to the Nabi XD it will require some force to separate them.
Right (R) speaker removal:
Remove one 4mm Phillips screw.
Use the metal spudger to separate the speaker from the frame.
The speaker is glued to the Nabi XD it will require some force to separate them.
Step 13
- Remove the left (L) speaker wire from the frame by pulling it to the side and up.
- The wire in this step, is connected to the charging port. Removing it, is shown in detail on step 6.
Remove the left (L) speaker wire from the frame by pulling it to the side and up.
The wire in this step, is connected to the charging port. Removing it, is shown in detail on step 6.
Step 14
- Left (L) speaker removal:
- Remove two 4mm Phillips screws.
- Use the metal spudger to separate the speaker from the frame.
Left (L) speaker removal:
Remove two 4mm Phillips screws.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Marissa Schiereck
Member since: 09/15/2016
638 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
USF Tampa, Team 17-2, Blackwell Fall 2016
Member of USF Tampa, Team 17-2, Blackwell Fall 2016
USFT-BLACKWELL-F16S17G2
3 Members
12 Guides authored