Difficulty

Moderate

Steps

17

Time Required

                          30 minutes

Sections

6

  • Rear panel
  • 2 steps
  • Battery
  • 2 steps
  • Charging port
  • 2 steps
  • Motherboard
  • 5 steps
  • Speakers
  • 3 steps
  • Screen
  • 3 steps

Flags

0

  • BackNABI XD

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Rear panel
  • Use the plastic opening tool at the top left corner seam, then pry the corner apart.

Use the plastic opening tool at the top left corner seam, then pry the corner apart.

1024

Step 2

  • Next slide the plastic opening tool across the sides of the Nabi. It will slowly open.
  • There are small plastic clips that need to be release. Gently apply outwards pressure until the clips give.
  • Go around the NABI XD and separate the rear panel from the device.

Next slide the plastic opening tool across the sides of the Nabi. It will slowly open.

There are small plastic clips that need to be release. Gently apply outwards pressure until the clips give.

Go around the NABI XD and separate the rear panel from the device.

Step 3

              Battery
  • Place your fingernails on both sides of the connector and pull it straight back away from the holder.

Place your fingernails on both sides of the connector and pull it straight back away from the holder.

Step 4

  • Battery is glued to the base, lift carefully.
  • To remove battery, lift the battery up from the motherboard.

Battery is glued to the base, lift carefully.

To remove battery, lift the battery up from the motherboard.

Step 5

              Charging port
  • Remove the two 4mm Phillips screws with the PH#0 screwdriver.
  • Disconnect the left (L) speaker wire from the charging port by grabbing it on both sides with the tweezers and pulling straight back.

Remove the two 4mm Phillips screws with the PH#0 screwdriver.

Disconnect the left (L) speaker wire from the charging port by grabbing it on both sides with the tweezers and pulling straight back.

Step 6

  • Use your fingernails or a spudger to flip up the small retaining flap, then pull the ribbon straight back to remove
  • Lift the charging port from the NABI XD.

Use your fingernails or a spudger to flip up the small retaining flap, then pull the ribbon straight back to remove

Lift the charging port from the NABI XD.

Step 7

              Motherboard
  • To remove the marked ribbons, use your fingernails or a spudger to lift up small tab
  • Use the Precision Tweezers to gently pull the ribbons straight out of the connectors.
  • You need to remove 4 ribbons

To remove the marked ribbons, use your fingernails or a spudger to lift up small tab

Use the Precision Tweezers to gently pull the ribbons straight out of the connectors.

You need to remove 4 ribbons

Step 8

  • Disconnect the camera by lifting the ribbon straight up. Also disconnect the remaining ribbon by lifting up gently.
  • To disconnect antenna wire, use the tweezers to pry connector straight from the board.

Disconnect the camera by lifting the ribbon straight up. Also disconnect the remaining ribbon by lifting up gently.

To disconnect antenna wire, use the tweezers to pry connector straight from the board.

Step 9

  • Disconnect the Right speaker by grabbing the wire head by its sides and pulling it back from the connector.

Disconnect the Right speaker by grabbing the wire head by its sides and pulling it back from the connector.

Step 10

  • Remove the four 4mm Phillips screws with the PH#0 screwdriver.

Remove the four 4mm Phillips screws with the PH#0 screwdriver.

Step 11

  • Lift the motherboard up away from the Nabi XD.

Lift the motherboard up away from the Nabi XD.

Step 12

              Speakers
  • Right (R) speaker removal:
  • Remove one 4mm Phillips screw.
  • Use the metal spudger to separate the speaker from the frame.
  • The speaker is glued to the Nabi XD it will require some force to separate them.

Right (R) speaker removal:

Remove one 4mm Phillips screw.

Use the metal spudger to separate the speaker from the frame.

The speaker is glued to the Nabi XD it will require some force to separate them.

Step 13

  • Remove the left (L) speaker wire from the frame by pulling it to the side and up.
  • The wire in this step, is connected to the charging port. Removing it, is shown in detail on step 6.

Remove the left (L) speaker wire from the frame by pulling it to the side and up.

The wire in this step, is connected to the charging port. Removing it, is shown in detail on step 6.

Step 14

  • Left (L) speaker removal:
  • Remove two 4mm Phillips screws.
  • Use the metal spudger to separate the speaker from the frame.

Left (L) speaker removal:

Remove two 4mm Phillips screws.

Step 15

              Screen
  • The ribbons are glued to the frame so gently lift them up without ripping them.
  • Lightly lift the marked wires and ribbons from the frame by gently pulling them in the direction of the arrows and up.
  • Remove five 4mm Phillips screws from the frame.

The ribbons are glued to the frame so gently lift them up without ripping them.

Lightly lift the marked wires and ribbons from the frame by gently pulling them in the direction of the arrows and up.

Remove five 4mm Phillips screws from the frame.

Step 16

  • Use the Plastic Opening tools to lift the frame up.
  • The ribbons need to be detangled from the frame while you are lifting it up.
  • Do not yank the frame away from the Nabi XD it is connect to it by a ribbon. Gently lift.

Use the Plastic Opening tools to lift the frame up.

The ribbons need to be detangled from the frame while you are lifting it up.

Do not yank the frame away from the Nabi XD it is connect to it by a ribbon. Gently lift.

Step 17

  • Lift the screen up with the black spudger.
  • Lift the frame up slowly and place it to the side.

Lift the screen up with the black spudger.

Lift the frame up slowly and place it to the side.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Marissa Schiereck

Member since: 09/15/2016

638 Reputation

                                      6 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       USF Tampa, Team 17-2, Blackwell Fall 2016                        

                                                  Member of USF Tampa, Team 17-2, Blackwell Fall 2016 



                    USFT-BLACKWELL-F16S17G2                     


                                            3 Members                     


                                            12 Guides authored

Kevin Fifer - Feb 10, 2017

Reply

Will the screen from an A or C model work with a B model?