Difficulty
Moderate
Steps
13
Time Required
30 - 40 minutes
Sections
3
- Rear Case
- 4 steps
- Motherboard
- 5 steps
- Screen
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackNabi Jr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Rear Case
- Remove the red rubber case from the device. This should come off with ease.
Remove the red rubber case from the device. This should come off with ease.
1024
Step 2
- Turn the device so the screen is facing away from you.
- Using a philips head, size #00, screwdriver, remove the screws in each corner of the plastic casing.(total of 4 screws)
Turn the device so the screen is facing away from you.
Using a philips head, size #00, screwdriver, remove the screws in each corner of the plastic casing.(total of 4 screws)
Step 3
- Remove the device casing using a small plastic pry bar.
- This might take a little bit of force to accomplish, don’t be afraid to go at it with a little gusto.
Remove the device casing using a small plastic pry bar.
This might take a little bit of force to accomplish, don’t be afraid to go at it with a little gusto.
Step 4
- After loosening the back cover, remove it from the device so you can get at the innards.
After loosening the back cover, remove it from the device so you can get at the innards.
Step 5
Motherboard
- Use the Philips #00 screwdriver to remove the 5 screws from the motherboard
Use the Philips #00 screwdriver to remove the 5 screws from the motherboard
Step 6
- De-solder the grey wire from motherboard
De-solder the grey wire from motherboard
Step 7
- Use tweezers to peel off all yellow tape from the motherboard
- Yellow tape is used in all locations where there is ribbon cable present.
Use tweezers to peel off all yellow tape from the motherboard
Yellow tape is used in all locations where there is ribbon cable present.
Step 8
- Remove all three ribbon cables from the motherboard by lifting up the locking tabs.
- Pull black locking tabs up in opposite direction of ribbon cable to remove.
- Use tweezers to pull the ribbon cable out of the locking tab’s slot
Remove all three ribbon cables from the motherboard by lifting up the locking tabs.
Pull black locking tabs up in opposite direction of ribbon cable to remove.
Use tweezers to pull the ribbon cable out of the locking tab’s slot
Step 9
- Lift motherboard to separate it the from the case shell.
Lift motherboard to separate it the from the case shell.
Step 10
Screen
- Remove the 6 screws that hold the screen in place
Remove the 6 screws that hold the screen in place
Step 11
- Remove the screen from the front casing
Remove the screen from the front casing
Step 12
- Separate the screen from the plastic casing.
Separate the screen from the plastic casing.
Step 13
- Replace the old screen with the new screen
Replace the old screen with the new screen
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Jimmy Nguyen
Member since: 03/24/2015
271 Reputation
2 Guides authored
Badges:
15
+12 more badges
Team
UMass Dartmouth, Team 4-3, Vijaybhaskar Spring 2015
Member of UMass Dartmouth, Team 4-3, Vijaybhaskar Spring 2015
UMASSD-VIJAYBHASKAR-S15S4G3
3 Members
12 Guides authored
Katie - Mar 13, 2016
Reply
Do you know of anywhere I can send a nabi jr to have a cracked screen replaced?
davemel - Dec 29, 2016
Reply
Yes thank you for the information but where do we find a screen to replace this?
vane.lpz - Mar 22, 2019
Reply
My navi jr is the nick jr edition and looks a bit different inside. I replaced the screen, as mentioned here but has to remove the outter glass-like screen that has the second smaller ribbonattach from the original screen, and put it on my screen because the new screen did not have that part. All buttons work, the screen looks perfect and vibrant, but the EFEN TOUCH Does not work!!! What did I do wrong? I attached all the ribbons properly!!!