Nabi Dreamtab Hd8 Speaker Replacement Repair Guide

Difficulty

Very easy

Steps

Time Required

                          5 minutes

Sections

Front Panel Assembly
7 steps
Speaker
2 steps

Flags

BackNabi DreamTab HD8
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Front Panel Assembly

Position the Nabi DreamTab onto a non-metallic surface so that the screen is facing towards the ceiling, and the DreamTab logo appears closest to you.
Remove the red silicone case from the Nabi DreamTab HD8.
These steps are specific to the included manufacturer case. If you have a different protective case, please refer to the respective manual for removal.

Position the Nabi DreamTab onto a non-metallic surface so that the screen is facing towards the ceiling, and the DreamTab logo appears closest to you.

Remove the red silicone case from the Nabi DreamTab HD8.

These steps are specific to the included manufacturer case. If you have a different protective case, please refer to the respective manual for removal.

1024

Step 2

Turn it upside down, ensuring the small black circular camera is in the upper left hand corner.
Proceeding beyond here will void the manufacturer’s warranty. If you wish to continue, follow these steps carefully.

Turn it upside down, ensuring the small black circular camera is in the upper left hand corner.

Proceeding beyond here will void the manufacturer’s warranty. If you wish to continue, follow these steps carefully.

Step 3

Remove the six 2.5 mm JIS #000 screws attaching the custom grid to the back panel.

Remove the six 2.5 mm JIS #000 screws attaching the custom grid to the back panel.

Step 4

Grasp one of the protruding squares and gently lift off the back plate. Place it aside for later reassembly.
This piece should come off very easily. If you have trouble removing it, all of the screws may not be completely removed. Check and proceed.
Do not confuse the golden threads for screws.

Grasp one of the protruding squares and gently lift off the back plate. Place it aside for later reassembly.

This piece should come off very easily. If you have trouble removing it, all of the screws may not be completely removed. Check and proceed.

Do not confuse the golden threads for screws.

Step 5

Remove the three 3.5mm screws using the J-0 screwdriver attaching the back panel to the device.

Remove the three 3.5mm screws using the J-0 screwdriver attaching the back panel to the device.

Step 6

Rotate the top of the device towards you so that the audio jack appears on the right side of the device.
The audio jack will have a small symbol of headphones next to a small 3.5mm diameter hole.
Wedge the plastic opening tool between where the front and back case panels meet near the audio jack.
Pry the device open using moderate force until you hear a clicking sound. This is the sound of the clips unlocking.
Move along the perimeter of the entire device using the same prying motion to gradually separate the front and back panels.
Once the edges are open return to the same starting position next to the audio jack.
During this step, you may crack some parts of the case. Gently pry around the speakers, audio jack and charging cable ports to reduce this damage.

Rotate the top of the device towards you so that the audio jack appears on the right side of the device.

The audio jack will have a small symbol of headphones next to a small 3.5mm diameter hole.

Wedge the plastic opening tool between where the front and back case panels meet near the audio jack.

Pry the device open using moderate force until you hear a clicking sound. This is the sound of the clips unlocking.

Move along the perimeter of the entire device using the same prying motion to gradually separate the front and back panels.

Once the edges are open return to the same starting position next to the audio jack.

During this step, you may crack some parts of the case. Gently pry around the speakers, audio jack and charging cable ports to reduce this damage.

Step 7

Once you’ve completed separating the front and back panels, place the device back onto the table, display facing downward and camera at the top left.
Lift off the back panel and rotate the device 180 degrees while the screen is facing down.

Once you’ve completed separating the front and back panels, place the device back onto the table, display facing downward and camera at the top left.

Lift off the back panel and rotate the device 180 degrees while the screen is facing down.

Step 8

              Speaker

The speakers are located on either side of the open device. Both are labeled as L and R for distinction.
Remove the four silver 2.5mm Phillips #000 screws.

The speakers are located on either side of the open device. Both are labeled as L and R for distinction.

Remove the four silver 2.5mm Phillips #000 screws.

Step 9

In addition to the four 2.5 mm screws, the speakers are physically connected to the motherboard via cables.
Using the plastic opening tool, disconnect the connectors at this location to completely free the speakers.
These components fit very snugly together, so make sure to use firm pressure to disengage the connectors. Avoid fingers from slipping to prevent injury on other sharp components of the object.

In addition to the four 2.5 mm screws, the speakers are physically connected to the motherboard via cables.

Using the plastic opening tool, disconnect the connectors at this location to completely free the speakers.

These components fit very snugly together, so make sure to use firm pressure to disengage the connectors. Avoid fingers from slipping to prevent injury on other sharp components of the object.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors

                    JayRam

Member since: 09/17/2015

261 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       CSU Fullerton, Team 2-3, Bruce Fall 2015                        

                                                  Member of CSU Fullerton, Team 2-3, Bruce Fall 2015 



                    CSUF-BRUCE-F15S2G3                     


                                            4 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team