Difficulty
Difficult
Steps
13
Time Required
30 minutes
Sections
3
- Face plate
- 7 steps
- Frame Removal
- 1 step
- Speaker
- 5 steps
Flags
0
BackMunchkin Mozart Magic Cube
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Face plate
- Remove two 6 mm Phillips #2 screws on either side of the On/Off Plate.
Remove two 6 mm Phillips #2 screws on either side of the On/Off Plate.
1024
Step 2
- Remove the On/Off switch plate and save the screws so you can use them later to put the plate back on.
Remove the On/Off switch plate and save the screws so you can use them later to put the plate back on.
Step 3
- Gently pull out the battery cartridge and if needed, replace the batteries with 3 AA alkaline batteries.
Gently pull out the battery cartridge and if needed, replace the batteries with 3 AA alkaline batteries.
Step 4
- Starting with the yellow face, insert the metal spudger between the yellow face and the white frame, prying the frame apart.
Starting with the yellow face, insert the metal spudger between the yellow face and the white frame, prying the frame apart.
Step 5
- Insert the metal spudger in the space created by the plastic opening tool between the frame and face of the cube.
- Pry the cube face from the frame.
Insert the metal spudger in the space created by the plastic opening tool between the frame and face of the cube.
Pry the cube face from the frame.
Step 6
- After removing the square plates, you can unscrew the screws underneath.
- Remove four 6 mm Phillips #2 screws, located on the sides.
After removing the square plates, you can unscrew the screws underneath.
Remove four 6 mm Phillips #2 screws, located on the sides.
Step 7
- Remove the rubber corners by simply pulling them off.
Remove the rubber corners by simply pulling them off.
Step 8
Frame Removal
- Remove twenty-four 6 mm Phillips #2 from all 6 sides.
- Once the screws are removed, gently pull apart the frame.
Remove twenty-four 6 mm Phillips #2 from all 6 sides.
Once the screws are removed, gently pull apart the frame.
Step 9
Speaker
- Remove four 6 mm Phillips #2 screws that hold down the speaker to its plastic frame.
Remove four 6 mm Phillips #2 screws that hold down the speaker to its plastic frame.
Step 10
- Remove two 6 mm Phillips #2 screws holding down the main motherboard to plastic frame.
Remove two 6 mm Phillips #2 screws holding down the main motherboard to plastic frame.
Step 11
- Gently remove speaker and motherboard from plastic frame.
Gently remove speaker and motherboard from plastic frame.
Step 12
- Desolder speaker cable connections
- For soldering instructions please see this additional guide How To Solder and Desolder Connections
Desolder speaker cable connections
For soldering instructions please see this additional guide How To Solder and Desolder Connections
Step 13
- Desolder speaker cable connections from the motherboard.
- If you’re unsure which metal connector to unsolder note that SPK is written next to the metal spot,
Desolder speaker cable connections from the motherboard.
If you’re unsure which metal connector to unsolder note that SPK is written next to the metal spot,
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Paula Campos
Member since: 08/27/2015
126 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
USF Tampa, Team 1-4, Sullivan Fall 2015
Member of USF Tampa, Team 1-4, Sullivan Fall 2015
USFT-SULLIVAN-F15S1G4
4 Members
7 Guides authored