Difficulty
Moderate
Steps
12
Time Required
15 minutes
Sections
3
- Face plate
- 7 steps
- Frame Removal
- 1 step
- Light
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackMunchkin Mozart Magic Cube
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Face plate
- Remove two 6 mm Phillips #2 screws on either side of the On/Off Plate.
Remove two 6 mm Phillips #2 screws on either side of the On/Off Plate.
1024
Step 2
- Remove the On/Off switch plate and save the screws so you can use them later to put the plate back on.
Remove the On/Off switch plate and save the screws so you can use them later to put the plate back on.
Step 3
- Gently pull out the battery cartridge and if needed, replace the batteries with 3 AA alkaline batteries.
Gently pull out the battery cartridge and if needed, replace the batteries with 3 AA alkaline batteries.
Step 4
- Starting with the yellow face, insert the metal spudger between the yellow face and the white frame, prying the frame apart.
Starting with the yellow face, insert the metal spudger between the yellow face and the white frame, prying the frame apart.
Step 5
- Insert the metal spudger in the space created by the plastic opening tool between the frame and face of the cube.
- Pry the cube face from the frame.
Insert the metal spudger in the space created by the plastic opening tool between the frame and face of the cube.
Pry the cube face from the frame.
Step 6
- After removing the square plates, you can unscrew the screws underneath.
- Remove four 6 mm Phillips #2 screws, located on the sides.
After removing the square plates, you can unscrew the screws underneath.
Remove four 6 mm Phillips #2 screws, located on the sides.
Step 7
- Remove the rubber corners by simply pulling them off.
Remove the rubber corners by simply pulling them off.
Step 8
Frame Removal
- Remove twenty-four 6 mm Phillips #2 from all 6 sides.
- Once the screws are removed, gently pull apart the frame.
Remove twenty-four 6 mm Phillips #2 from all 6 sides.
Once the screws are removed, gently pull apart the frame.
Step 9
Light
- Flip the frame over so that green motherboard over so that the LED is face down and the brown side of the motherboard is face up.
- Use the Jimmy to remove the glue connecting the motherboard to the white frame.
Flip the frame over so that green motherboard over so that the LED is face down and the brown side of the motherboard is face up.
Use the Jimmy to remove the glue connecting the motherboard to the white frame.
Step 10
- Slide the motherboard out of the frame.
Slide the motherboard out of the frame.
Step 11
- Use the soldering iron to desolder the LED by applying heat to the half sphere like connections.
- For soldering instructions please see this additional guide How To Solder and Desolder Connections
Use the soldering iron to desolder the LED by applying heat to the half sphere like connections.
For soldering instructions please see this additional guide How To Solder and Desolder Connections
Step 12
- Take the new LED and solder the two legs back to the motherboard.
Take the new LED and solder the two legs back to the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Nikolas Soulandros
Member since: 08/27/2015
291 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
USF Tampa, Team 1-4, Sullivan Fall 2015
Member of USF Tampa, Team 1-4, Sullivan Fall 2015
USFT-SULLIVAN-F15S1G4
4 Members
7 Guides authored