Difficulty
Easy
Steps
12
Time Required
55 minutes - 1 hour
Sections
1
- LCD Screen
- 12 steps
Flags
0
BackMSI GS60 6QE Ghost Pro 4K
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
LCD Screen
- Remove the eleven 5mm screws with a Phillips #1 screwdriver.
- Remove the four 2.5mm screws with a Phillips #1 screwdriver.
Remove the eleven 5mm screws with a Phillips #1 screwdriver.
Remove the four 2.5mm screws with a Phillips #1 screwdriver.
1024
Step 2
- Remove the bottom plate from the laptop. Using a prying tool to slide between the bottom plate and chassis will result in easier removal.
Remove the bottom plate from the laptop. Using a prying tool to slide between the bottom plate and chassis will result in easier removal.
Step 3
- Remove the four 2.5mm screws using a Phillips #1 bit.
Remove the four 2.5mm screws using a Phillips #1 bit.
Step 4
- Carefully pry the screen assembly from the chassis on both sides. Use caution as the cable to the screen is located on the right bracket.
Carefully pry the screen assembly from the chassis on both sides. Use caution as the cable to the screen is located on the right bracket.
Step 5
- Lay the components out as shown.
- The rightmost of the two cable connections is located under sticky tape. Remove the tape to access it and unseat from the connection.
- The other connection is removed by gently pulling up on the black grip tape.
Lay the components out as shown.
The rightmost of the two cable connections is located under sticky tape. Remove the tape to access it and unseat from the connection.
The other connection is removed by gently pulling up on the black grip tape.
Step 6
- Gently feed both connections under the red, white, and yellow cables from the fan.
- Note that both cables will meet and form a singular cable.
Gently feed both connections under the red, white, and yellow cables from the fan.
Note that both cables will meet and form a singular cable.
Step 7
- Gently lift up on the back of the fan and remove the routed cable.
Gently lift up on the back of the fan and remove the routed cable.
Step 8
- Using a prying tool, find the seam where the two pieces of screen meet and begin separating them.
- Use caution, as there is glue and snapping clips holding them together.
- Work around the perimeter, separating the pieces with the prying tool as you go.
Using a prying tool, find the seam where the two pieces of screen meet and begin separating them.
Use caution, as there is glue and snapping clips holding them together.
Work around the perimeter, separating the pieces with the prying tool as you go.
Step 9
- Locate the metal bracket the cable is woven through.
- Unweave the cable from the bracket. This will give you extra length to work with the screen.
Locate the metal bracket the cable is woven through.
Unweave the cable from the bracket. This will give you extra length to work with the screen.
Step 10
- Remove two 2.5mm screws with a Phillips #1 screwdriver.
Remove two 2.5mm screws with a Phillips #1 screwdriver.
Step 11
- Remove the screen.
- Gently remove the yellow tape and then remove the connector.
Remove the screen.
Gently remove the yellow tape and then remove the connector.
Step 12
- The defective screen is now completely removed and ready to be replaced.
The defective screen is now completely removed and ready to be replaced.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Coty Mast
Member since: 11/10/2018
259 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
IUPUI, Team S1-G1, Wilson Fall 2018
Member of IUPUI, Team S1-G1, Wilson Fall 2018
IUPUI-WILSON-F18S1G1
4 Members
1 Guide authored
