Mpow 059 Battery Replacement Repair Guide

Difficulty

Difficult

Steps

5

Time Required

                          15 - 30 minutes            

Sections

2

• Ear Cushion
• 2 steps
• Battery
• 3 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

• BackMpow 059

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

Note: If possible, make sure your battery is completely depleted before replacing it. If a lithium-ion battery is punctured during replacement, it may spark and create a fire.

What you need

Step 1

              Ear Cushion               

• Place the iFixit opening tool between the soft ear cushion and the hard plastic of the speaker.
• Pry the soft ear cushion away from the hard plastic using a moderate amount of pressure.
• There is adhesive holding the ear cushion to the speaker so it may take a little patience to remove.
• Applying too much pressure can damage ear cushion.

Place the iFixit opening tool between the soft ear cushion and the hard plastic of the speaker.

Pry the soft ear cushion away from the hard plastic using a moderate amount of pressure.

There is adhesive holding the ear cushion to the speaker so it may take a little patience to remove.

Applying too much pressure can damage ear cushion.

1024

Step 2

• Remove the ear cushion away from the speaker to completely detach it from the headphones.

Remove the ear cushion away from the speaker to completely detach it from the headphones.

Step 3

              Battery               

• Use the Phillips #1 screwdriver to remove the six screws holding the red plastic cover in place.
• Carefully peel the plastic cover off the left cup to reveal the ear cup’s internal components.
• There is some adhesive holding the red cover down so be careful as you remove it so it doesn’t break or crack.

Use the Phillips #1 screwdriver to remove the six screws holding the red plastic cover in place.

Carefully peel the plastic cover off the left cup to reveal the ear cup’s internal components.

There is some adhesive holding the red cover down so be careful as you remove it so it doesn’t break or crack.

Step 4

• Use the JIS J00 screwdriver to remove the 3 screws that secure the black cover.

Use the JIS J00 screwdriver to remove the 3 screws that secure the black cover.

Step 5

• Remove the black cover to reveal the battery. The battery is attached to the back of the black cover.
• The plastic cover of the headphones is connected to the battery housing by a wire connector. Be careful not to harm this cable by pulling the cap too hard during disassembly.
• Undo the cable and remove the battery.

Remove the black cover to reveal the battery. The battery is attached to the back of the black cover.

The plastic cover of the headphones is connected to the battery housing by a wire connector. Be careful not to harm this cable by pulling the cap too hard during disassembly.

Undo the cable and remove the battery.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Danielle Furtado                     

Member since: 03/25/2022

322 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       UMass Dartmouth, Team E-1, Gurgel Spring 2022                        

                                                  Member of UMass Dartmouth, Team E-1, Gurgel Spring 2022 



                    UMASSD-GURGEL-S22SEG1                     


                                            3 Members                     


                                            4 Guides authored                     

Martin Dromigny - Nov 5, 2022

Reply

Hello

What kind of glue should I use to put new pad?

hdm_1@comcast.net - Dec 12, 2022

Reply

What is the part number for the replacement battery? Where can I find one?