Motorola Xoom 2 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Backplate
4 steps
Screen
8 steps

Flags

BackMotorola Xoom 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

If your Motorola Xoom 2’s (MZ615-16) screen is damaged and in need of a replacement this guide can help. Use caution when working on this part because the screen is very fragile.

What you need

Step 1

              Backplate

Pry off the silver top back cover (the panel around the camera) with iFixit opening picks or a similar implement.

Pry off the silver top back cover (the panel around the camera) with iFixit opening picks or a similar implement.

1024

Step 2

Using a T5 screwdriver, unscrew the four 1.5mm screws holding the main back cover. These screws are arranged in a line across the top of the back of the device.

Using a T5 screwdriver, unscrew the four 1.5mm screws holding the main back cover. These screws are arranged in a line across the top of the back of the device.

Step 3

Turn the device over and using a pry tool and the opening picks, gently apply pressure between the outside edge of the seal marked with the arrow. Slowly move around the edges of the device, applying even pressure, and separate the back plate from the display.
There is adhesive between the back-plate and battery.

Turn the device over and using a pry tool and the opening picks, gently apply pressure between the outside edge of the seal marked with the arrow. Slowly move around the edges of the device, applying even pressure, and separate the back plate from the display.

There is adhesive between the back-plate and battery.

Step 4

Remove the back plate from your device.

Remove the back plate from your device.

Step 5

              Screen

Using a pry tool, gently un-clip the orange ribbon cable attached to the left of the digitizer connector and fold the digitizer connector away from the device.

Using a pry tool, gently un-clip the orange ribbon cable attached to the left of the digitizer connector and fold the digitizer connector away from the device.

Step 6

Using a pry tool, gently apply force along the crevice between the digitizer board and the chassis.
Using your fingers, gently bend the digitizer board to the position.
This step is mandatory to completely remove the screen assembly.

Using a pry tool, gently apply force along the crevice between the digitizer board and the chassis.

Using your fingers, gently bend the digitizer board to the position.

This step is mandatory to completely remove the screen assembly.

Step 7

Unscrew the sixteen (16) 1.5mm screws using the T5 Torx screwdriver.
Two of the screws were previously hidden behind the digitizer connector.
The screw located in the top right of the device has a washer attached.

Unscrew the sixteen (16) 1.5mm screws using the T5 Torx screwdriver.

Two of the screws were previously hidden behind the digitizer connector.

The screw located in the top right of the device has a washer attached.

Step 8

Using a prying tool, unclip the four black plastic tabs on the shorter edges of the device.
Inserting opening picks between the digitizer and the casing may make the process easier by helping to keep the tabs un-clipped.
Do not touch the LCD underneath, keep it as clean as possible!

Using a prying tool, unclip the four black plastic tabs on the shorter edges of the device.

Inserting opening picks between the digitizer and the casing may make the process easier by helping to keep the tabs un-clipped.

Do not touch the LCD underneath, keep it as clean as possible!

Step 9

Carefully flip the device over and unfold the digitizer connector out from under the device.
Gently lift up on the bottom edge of the digitizer to remove it from the device.
Do not touch the LCD underneath, keep it as clean as possible!
From here the digitizer may be replaced with a new one, the next steps continue to replace the LCD.

Carefully flip the device over and unfold the digitizer connector out from under the device.

Gently lift up on the bottom edge of the digitizer to remove it from the device.

From here the digitizer may be replaced with a new one, the next steps continue to replace the LCD.

Step 10

Using an opening pick, gently lift the LCD from the casing.
Holding the screw tabs with your hands, fold the LCD gently down to reveal the LCD connector located at the bottom right of the device.
Do not touch the LCD surface, keep it as clean as possible!
The LCD and the underside of the new digitizer may be cleaned by gently brushing it with a microfiber cloth.

Using an opening pick, gently lift the LCD from the casing.

Holding the screw tabs with your hands, fold the LCD gently down to reveal the LCD connector located at the bottom right of the device.

Do not touch the LCD surface, keep it as clean as possible!

The LCD and the underside of the new digitizer may be cleaned by gently brushing it with a microfiber cloth.

Step 11

Gently lift up the tab and carefully pull it straight back, parallel to the cable, until the LCD cable is removed.
Slightly wiggling the tab can help to ease the connector apart.
Do not use excessive force to remove the connector, this risks the pins getting damaged rendering the cable and/or LCD unusable.

Gently lift up the tab and carefully pull it straight back, parallel to the cable, until the LCD cable is removed.

Slightly wiggling the tab can help to ease the connector apart.

Do not use excessive force to remove the connector, this risks the pins getting damaged rendering the cable and/or LCD unusable.

Step 12

Remove the LCD from the device.

Remove the LCD from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Enrique Escobar

Member since: 09/24/2019

486 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Embry-Riddle Aeronautical University, Team S13-G6, Lamothe Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S13-G6, Lamothe Fall 2019 



                    ERAU-LAMOTHE-F19S13G6                     


                                            4 Members                     


                                            7 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team