Difficulty
Moderate
Steps
14
Time Required
40 minutes
Sections
3
- Battery
- 2 steps
- Motherboard
- 6 steps
- Screen
- 6 steps
Flags
0
BackMotorola RIZR Z3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.
Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.
1024
Step 2
- Tilt the battery by lifting at the exposed notch.
- Slide the battery out of its casing.
Tilt the battery by lifting at the exposed notch.
Slide the battery out of its casing.
Step 3
Motherboard
- Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.
Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.
Step 4
- Use a plastic opening tool to lift the plastic casing.
- Pull the plastic casing directly away from the phone.
Use a plastic opening tool to lift the plastic casing.
Pull the plastic casing directly away from the phone.
Step 5
- Lift the black rubber loudspeaker housing up and out of the plastic casing.
Lift the black rubber loudspeaker housing up and out of the plastic casing.
Step 6
- Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.
- Caution: Remove carefully, if broken, the phone will not be able to make calls.
Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.
Caution: Remove carefully, if broken, the phone will not be able to make calls.
Step 7
- Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.
- Caution: Remove carefully, if broken, the phone will not function properly.
Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.
Caution: Remove carefully, if broken, the phone will not function properly.
Step 8
- Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.
- Caution: Do this gently Unclipping too fast may cause damage to your phone.
Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.
Caution: Do this gently Unclipping too fast may cause damage to your phone.
Step 9
Screen
- Turn the phone to the front.
- Push the keypad out through the plastic casing.
Turn the phone to the front.
Push the keypad out through the plastic casing.
Step 10
- Turn the phone to the side.
- Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.
Turn the phone to the side.
Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.
Step 11
- Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.
Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.
Step 12
- Use a spudger to pry the plastic screen casing partially up from the LCD unit.
- Use the spudger to pry the ribbon cable away from its clip on the LCD unit.
- Caution: If the LCD will not function properly if this ribbon cable is broken.
- Pull the plastic screen casing directly away from the LCD unit.
Use a spudger to pry the plastic screen casing partially up from the LCD unit.
Use the spudger to pry the ribbon cable away from its clip on the LCD unit.
Caution: If the LCD will not function properly if this ribbon cable is broken.
Pull the plastic screen casing directly away from the LCD unit.
Step 13
- Turn the plastic screen casing over.
- Carefully use a spudger to push the on the two clips holding the navigational pad in place.
- You may have to pry the pad away from the plastic screen casing with the spudger.
Turn the plastic screen casing over.
Carefully use a spudger to push the on the two clips holding the navigational pad in place.
You may have to pry the pad away from the plastic screen casing with the spudger.
Step 14
- Use a plastic opening tool to pry the screen up, being mindful of the glue holding the screen to its casing.
- Pull the screen directly away from the casing.
Use a plastic opening tool to pry the screen up, being mindful of the glue holding the screen to its casing.
Pull the screen directly away from the casing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Brooke Shuford
Member since: 10/10/2011
65 Reputation
3 Guides authored
Badges:
7
+4 more badges
Team
Cal Poly, Team 5-34, Amido Fall 2011
Member of Cal Poly, Team 5-34, Amido Fall 2011
CPSU-AMIDO-F11S5G34
4 Members
6 Guides authored