Motorola Rizr Z3 Lcd Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Battery
2 steps
Motherboard
6 steps
LCD
5 steps

Flags

BackMotorola RIZR Z3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.

Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.

1024

Step 2

Tilt the battery by lifting at the exposed notch.
Slide the battery out of its casing.

Tilt the battery by lifting at the exposed notch.

Slide the battery out of its casing.

Step 3

              Motherboard

Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.

Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.

Step 4

Use a plastic opening tool to lift the plastic casing.
Pull the plastic casing directly away from the phone.

Use a plastic opening tool to lift the plastic casing.

Pull the plastic casing directly away from the phone.

Step 5

Lift the black rubber loudspeaker housing up and out of the plastic casing.

Lift the black rubber loudspeaker housing up and out of the plastic casing.

Step 6

Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.
Caution: Remove carefully, if broken, the phone will not be able to make calls.

Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.

Caution: Remove carefully, if broken, the phone will not be able to make calls.

Step 7

Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.
Caution: Remove carefully, if broken, the phone will not function properly.

Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.

Caution: Remove carefully, if broken, the phone will not function properly.

Step 8

Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.
Caution: Do this gently Unclipping too fast may cause damage to your phone.

Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.

Caution: Do this gently Unclipping too fast may cause damage to your phone.

Step 9

LCD

Turn the phone to the front.
Push the keypad out through the plastic casing.

Turn the phone to the front.

Push the keypad out through the plastic casing.

Step 10

Turn the phone to the side.
Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.

Turn the phone to the side.

Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.

Step 11

Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.

Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.

Step 12

Use a spudger to pry the plastic screen casing partially up from the LCD unit.
Use the spudger to pry the ribbon cable away from its clip on the LCD unit.
Caution: Do this carefully, damage to this ribbon cable will cause a blank screen.
Pull the plastic screen casing directly away from the LCD unit.

Use a spudger to pry the plastic screen casing partially up from the LCD unit.

Use the spudger to pry the ribbon cable away from its clip on the LCD unit.

Caution: Do this carefully, damage to this ribbon cable will cause a blank screen.

Pull the plastic screen casing directly away from the LCD unit.

Step 13

Use a spudger to lift the LCD partially away from the metal casing.
Use the spudger to pry the ribbon cable directly up from its clip on the metal casing.
Caution: Damage to the ribbon cable here will cause screen damage.
Pull the LCD completely away from the metal casing.

Use a spudger to lift the LCD partially away from the metal casing.

Use the spudger to pry the ribbon cable directly up from its clip on the metal casing.

Caution: Damage to the ribbon cable here will cause screen damage.

Pull the LCD completely away from the metal casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors

                    Brooke Shuford

Member since: 10/10/2011

65 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team 5-34, Amido Fall 2011                        

                                                  Member of Cal Poly, Team 5-34, Amido Fall 2011 



                    CPSU-AMIDO-F11S5G34                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team