Motorola Razr Maxx Hd External Speaker Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          35 minutes

Sections

Screen Removal
4 steps
Circuit Board
7 steps
External Speaker
1 step

Flags

BackMotorola RAZR Maxx HD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen Removal

Use the Torx T5 Screwdriver to remove two 5.0 mm screws at the bottom of the phone.

Use the Torx T5 Screwdriver to remove two 5.0 mm screws at the bottom of the phone.

1024

Step 2

To remove the SIM card, use an unfolded paperclip to press down on the metal plate on the left side of the phone until it pops up.

To remove the SIM card, use an unfolded paperclip to press down on the metal plate on the left side of the phone until it pops up.

Step 3

Gently push the screen toward the top edge of the phone and tilt the screen to reveal the black flex cables.
Do NOT remove the screen all the way or the flex cables will be damaged.

Gently push the screen toward the top edge of the phone and tilt the screen to reveal the black flex cables.

Do NOT remove the screen all the way or the flex cables will be damaged.

Step 4

Release the two black ribbon flex cables by gently pulling up on the connection using the spudger. Then lift the screen to remove.
Make sure to remove the flex cables before completely removing the screen.
When reassembling, align the white bands on the edge of the screen so that a connection is made.

Release the two black ribbon flex cables by gently pulling up on the connection using the spudger. Then lift the screen to remove.

Make sure to remove the flex cables before completely removing the screen.

When reassembling, align the white bands on the edge of the screen so that a connection is made.

Step 5

              Circuit Board

Remove the plastic yellow tape on the battery connector using the spudger.
Pry up on the orange connection to release it from the motherboard.

Remove the plastic yellow tape on the battery connector using the spudger.

Pry up on the orange connection to release it from the motherboard.

Step 6

Unscrew all ten 4.0 mm screws on the motherboard using a T5 Torx screwdriver.

Unscrew all ten 4.0 mm screws on the motherboard using a T5 Torx screwdriver.

Step 7

Using tweezers, remove the clear plastic covering on the speaker.
Pry open the connection by lifting up on the speaker wire connector.

Using tweezers, remove the clear plastic covering on the speaker.

Pry open the connection by lifting up on the speaker wire connector.

Step 8

Using tweezers, remove the back facing camera cover.

Using tweezers, remove the back facing camera cover.

Step 9

Using the spudger tool, release the yellow ribbon cable on the headphone jack cover by pushing up on the connection.
Remove the cover from the motherboard.

Using the spudger tool, release the yellow ribbon cable on the headphone jack cover by pushing up on the connection.

Remove the cover from the motherboard.

Step 10

Release the yellow flex cable on the right side of the phone using the spudger by lifting up on the retaining clip.

Release the yellow flex cable on the right side of the phone using the spudger by lifting up on the retaining clip.

Step 11

Wedge the spudger between the motherboard and the back case.
Work your way around the entire edge of the motherboard to release it and remove it from the back of the phone.

Wedge the spudger between the motherboard and the back case.

Work your way around the entire edge of the motherboard to release it and remove it from the back of the phone.

Step 12

              External Speaker

Use tweezers to remove the speaker from the top left of the phone by pulling upward.

Use tweezers to remove the speaker from the top left of the phone by pulling upward.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Anna Sullivan

Member since: 02/01/2015

880 Reputation

                                      3 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 8-40, Amido Winter 2015                        

                                                  Member of Cal Poly, Team 8-40, Amido Winter 2015 



                    CPSU-AMIDO-W15S8G40                     


                                            5 Members                     


                                            18 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team