Motorola Moto Z Force Droid Lcd Screen And Digitizer Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

Opening Procedure
14 steps
LCD Screen and Digitizer Assembly
1 step

Flags

BackMotorola Moto Z Force Droid
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

For your safety, discharge your battery below 25% before disassembling your phone. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.

Before you begin, look at the last step and make sure your replacement part matches the one shown. This guide is for replacing a screen/display that is already installed in a new frame. If you bought a bare display instead, you will need to carefully separate your old display from your phone’s existing frame, and then glue the new display in. Those steps are not covered by this guide.

What you need

Step 1

              Opening Procedure

Apply a heated iOpener to the lower glass panel on the back of the phone for five minutes.
The panel is extremely stubborn, and you may need to reheat and reapply the iOpener several times to get the panel warm enough. Follow the iOpener instructions to avoid overheating.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Apply a heated iOpener to the lower glass panel on the back of the phone for five minutes.

The panel is extremely stubborn, and you may need to reheat and reapply the iOpener several times to get the panel warm enough. Follow the iOpener instructions to avoid overheating.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

1024

Step 2

Insert an opening pick into the small gap between the rear case and the glass panel.
The gap between the panel and the frame is very tight, so it may help to rock or slide the pick back and forth as you push it down into the gap. Alternatively, you can use a thin blade or metal pry tool to lift the panel before prying the rest of the way with a pick, but work slowly and gently to avoid damaging the glass.
If you’re having trouble inserting your pick, go back a step and heat the panel further. Loosening the panel requires significant heat, but avoid heating the middle of the phone where the battery is.
A few drops of high-concentration (at least 90%) isopropyl alcohol applied to the edges of the panel may help to loosen the adhesive as well.
Do not pry over the charging port. It is framed with plastic that can be damaged when prying.
With tip of the pick under the glass panel, carefully pry upward to slightly separate the rear case and the panel.

Insert an opening pick into the small gap between the rear case and the glass panel.

The gap between the panel and the frame is very tight, so it may help to rock or slide the pick back and forth as you push it down into the gap. Alternatively, you can use a thin blade or metal pry tool to lift the panel before prying the rest of the way with a pick, but work slowly and gently to avoid damaging the glass.

If you’re having trouble inserting your pick, go back a step and heat the panel further. Loosening the panel requires significant heat, but avoid heating the middle of the phone where the battery is.

A few drops of high-concentration (at least 90%) isopropyl alcohol applied to the edges of the panel may help to loosen the adhesive as well.

Do not pry over the charging port. It is framed with plastic that can be damaged when prying.

With tip of the pick under the glass panel, carefully pry upward to slightly separate the rear case and the panel.

Step 3

Slide the pick in between the panel and the rear case.
Slide the pick across the length of the panel to slice the adhesive holding it to the rear case.

Slide the pick in between the panel and the rear case.

Slide the pick across the length of the panel to slice the adhesive holding it to the rear case.

Step 4

Use the opening pick to carefully pry up the glass panel.
Remove the glass panel.

Use the opening pick to carefully pry up the glass panel.

Remove the glass panel.

Step 5

Repeat the previous four heating and removal steps for the upper glass panel.
During reassembly, remove leftover adhesive from the panels and the rear case. Then clean those areas with high concentration isopropyl alcohol (greater than 90%) and a lint-free cloth. This will ensure proper adhesion of the panels.
Reinstall the panels using a pre-cut adhesive strip or double-sided tape.

Repeat the previous four heating and removal steps for the upper glass panel.

During reassembly, remove leftover adhesive from the panels and the rear case. Then clean those areas with high concentration isopropyl alcohol (greater than 90%) and a lint-free cloth. This will ensure proper adhesion of the panels.

Reinstall the panels using a pre-cut adhesive strip or double-sided tape.

Step 6

Remove the six 4 mm T3 Torx screws securing the display assembly.

Remove the six 4 mm T3 Torx screws securing the display assembly.

Step 7

Insert the point of a spudger into the hole in the bottom right corner of the rear case.
Press the spudger into the hole to separate the display from the rear case.

Insert the point of a spudger into the hole in the bottom right corner of the rear case.

Press the spudger into the hole to separate the display from the rear case.

Step 8

Use a finger to maintain separation between the display assembly and the rear case while you remove the spudger.
Reinsert the flat end of the spudger in the gap between the display assembly and the rear case.

Use a finger to maintain separation between the display assembly and the rear case while you remove the spudger.

Reinsert the flat end of the spudger in the gap between the display assembly and the rear case.

Step 9

Slide the spudger along the side of the phone until you get to the clip securing the display to the rear case.
With the spudger right next to the clip, carefully twist the spudger to pry the display away from the rear case and release the clip.

Slide the spudger along the side of the phone until you get to the clip securing the display to the rear case.

With the spudger right next to the clip, carefully twist the spudger to pry the display away from the rear case and release the clip.

Step 10

Repeat the separation and prying process for the other side of the phone.
There is one clip on each side of the phone—make sure both are free before you continue.
Be careful not to separate the bottom edge of the display more than 0.5 inches (13 mm) from the rear case. The display cable is still connected and can be damaged if the bottom of the phone is opened too far.

Repeat the separation and prying process for the other side of the phone.

There is one clip on each side of the phone—make sure both are free before you continue.

Be careful not to separate the bottom edge of the display more than 0.5 inches (13 mm) from the rear case. The display cable is still connected and can be damaged if the bottom of the phone is opened too far.

Step 11

Tilt the top right corner of the display down to disengage one of the tabs that secure the top of the display.
Tilt the other corner down next, to disengage the other tab.
The display cable is still connected and can be damaged by too much display movement. Tilt the display carefully and stop if you encounter significant resistance.

Tilt the top right corner of the display down to disengage one of the tabs that secure the top of the display.

Tilt the other corner down next, to disengage the other tab.

The display cable is still connected and can be damaged by too much display movement. Tilt the display carefully and stop if you encounter significant resistance.

Step 12

Lift the right edge of the display to hinge the phone open like a book, no more than 45°.
Gently lift the display enough to clear the clip from the edge of the rear case, maintaining the 45º angle.
Rest the display on the table behind the phone and open to 90º to allow access to the display cable.

Lift the right edge of the display to hinge the phone open like a book, no more than 45°.

Gently lift the display enough to clear the clip from the edge of the rear case, maintaining the 45º angle.

Rest the display on the table behind the phone and open to 90º to allow access to the display cable.

Step 13

Use the flat end of a spudger to lift the display cable connector up out of its socket.
Only pry up on the display connector itself and not the socket on the motherboard.
At this point during reassembly after the display is connected, turn the phone on and verify that the display functions correctly. If it does, turn the phone off and proceed with reassembly.
If it does not work, check that everything is assembled correctly and the connectors are clean. For further troubleshooting, visit our Answers Forum.

Use the flat end of a spudger to lift the display cable connector up out of its socket.

Only pry up on the display connector itself and not the socket on the motherboard.

At this point during reassembly after the display is connected, turn the phone on and verify that the display functions correctly. If it does, turn the phone off and proceed with reassembly.

If it does not work, check that everything is assembled correctly and the connectors are clean. For further troubleshooting, visit our Answers Forum.

Step 14

Remove the display.
During reassembly, if you wish to replace the display adhesive strips, first use a spudger to scrape away all the old adhesive, and clean the adhesion area with some high-concentration (at least 90%) isopropyl alcohol on a lint-free cloth.
Apply a thin, high-bond tape, like 1 mm Tesa 61395, or a strip from a precut adhesive card, where the old adhesive was.
If you’re installing a new display assembly, note where the adhesive is on the original assembly and apply adhesive in the same places on the new assembly.

Remove the display.

During reassembly, if you wish to replace the display adhesive strips, first use a spudger to scrape away all the old adhesive, and clean the adhesion area with some high-concentration (at least 90%) isopropyl alcohol on a lint-free cloth.

Apply a thin, high-bond tape, like 1 mm Tesa 61395, or a strip from a precut adhesive card, where the old adhesive was.

If you’re installing a new display assembly, note where the adhesive is on the original assembly and apply adhesive in the same places on the new assembly.

Step 15

              LCD Screen and Digitizer Assembly

Only the LCD screen and digitizer assembly remains.
Check carefully to make sure your replacement part matches, and that you’ve removed all the necessary parts from the old frame for installation in the new one.

Only the LCD screen and digitizer assembly remains.

Check carefully to make sure your replacement part matches, and that you’ve removed all the necessary parts from the old frame for installation in the new one.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 7 other contributors

                    Adam O'Camb

Member since: 04/11/2015

173,479 Reputation

                                      418 Guides authored                  



                       Badges:
                       39







                                                        +36 more badges

Introduction#

What you need#

Introduction

What you need