Difficulty
Moderate
Steps
6
Time Required
30 minutes
Sections
2
- Screen
- 4 steps
- Battery
- 2 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackMotorola Moto G7 Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Remove the Screen
- Insert an opening tool pick under the screen, starting at the top of the phone.
- Slide the pick around the entire perimeter of the display to break the adhesive.
- There is a cable on the right side of the phone (the side with the volume buttons), which connects the screen to the rest of the phone. Be careful not to damage this cable.
- Once enough adhesive has been removed, you should be able to separate the screen by gently lifting it from the left side of the phone.
- While not necessary, applying a gentle heat to the edges of the display with a heat gun or iOpener will weaken the adhesive.
Insert an opening tool pick under the screen, starting at the top of the phone.
Slide the pick around the entire perimeter of the display to break the adhesive.
There is a cable on the right side of the phone (the side with the volume buttons), which connects the screen to the rest of the phone. Be careful not to damage this cable.
Once enough adhesive has been removed, you should be able to separate the screen by gently lifting it from the left side of the phone.
While not necessary, applying a gentle heat to the edges of the display with a heat gun or iOpener will weaken the adhesive.
1024
Step 2
Remove the Display Cable Cover
- Remove the three 2.7 mm screws that surround the base of the display cable using the Torx T5 screwdriver.
- Gently remove the metal piece that covers the base of the display cable.
Remove the three 2.7 mm screws that surround the base of the display cable using the Torx T5 screwdriver.
Gently remove the metal piece that covers the base of the display cable.
Step 3
- Use the pointed end of the spudger to lift the metal casing where circled.
Use the pointed end of the spudger to lift the metal casing where circled.
Step 4
Separate the Display From the Phone
- Underneath this metal piece is the base of the cable. Use a spudger to vertically lift the connection out of its port.
Underneath this metal piece is the base of the cable. Use a spudger to vertically lift the connection out of its port.
Step 5
Cut the Black Tape and the Connector Before Removal
- Use the blade end of a Halberd Spudger to cut through the two strips of black tape attached to the battery.
- Use the flat end of a spudger to disconnect the battery from the phone.
Use the blade end of a Halberd Spudger to cut through the two strips of black tape attached to the battery.
Use the flat end of a spudger to disconnect the battery from the phone.
Step 6
Remove the Battery
- Take the battery out with the flat end of the spudger.
- Handling batteries can be dangerous. Be very careful not to puncture the battery, as there are dangerous chemicals inside. Physical damage to the battery can cause it to burst into flame and release toxic smoke.
Take the battery out with the flat end of the spudger.
Handling batteries can be dangerous. Be very careful not to puncture the battery, as there are dangerous chemicals inside. Physical damage to the battery can cause it to burst into flame and release toxic smoke.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
with 11 other contributors
Jack Browers
Member since: 02/10/2020
299 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
Cal Poly, Team S22-G5, Regan Winter 2020
Member of Cal Poly, Team S22-G5, Regan Winter 2020
CPSU-REGAN-W20S22G5
5 Members
17 Guides authored
Mrs Glue - Aug 15, 2021
Reply
bricked, the display is not recognized anymore after re-attaching
as an additional information: my phone is bricked, because i severed a connection of the display, which is located at the bottom of the phone - you should only enter the pick up to a depth of ~ 2-3mm at the bottom!