Difficulty

Moderate

Steps

8

Time Required

                          15 - 25 minutes

Sections

3

  • Back Cover
  • 3 steps
  • Motherboard
  • 4 steps
  • Speaker
  • 1 step

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackMotorola Moto G7 Play

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Turn off your device before you begin.
  • Use the iFixit pick to break the adhesive around the back case.
  • Use a heat gun, hairdryer, or iOpener to weaken the adhesive around the back case. If you’re using the iOpener, please review the instructions for proper use.

Turn off your device before you begin.

Use the iFixit pick to break the adhesive around the back case.

Use a heat gun, hairdryer, or iOpener to weaken the adhesive around the back case. If you’re using the iOpener, please review the instructions for proper use.

1024

Step 2

  • Detach the back case from the phone.
  • Make sure the back is opened right to left so the cable of the fingerprint scanner does not get damaged.

Detach the back case from the phone.

Make sure the back is opened right to left so the cable of the fingerprint scanner does not get damaged.

Step 3

  • Use the iFixit pick and the iFixit opening tool to pull the fingerprint scanner off of the back case.

Use the iFixit pick and the iFixit opening tool to pull the fingerprint scanner off of the back case.

Step 4

              Motherboard
  • Remove the nine 3.2mm screws from the motherboard cover with a Phillips #00 screwdriver.

Remove the nine 3.2mm screws from the motherboard cover with a Phillips #00 screwdriver.

Step 5

  • Lift motherboard cover off by the bottom.
  • Use reverse tweezers or a similar tool if needed.

Lift motherboard cover off by the bottom.

Use reverse tweezers or a similar tool if needed.

Step 6

  • Once the motherboard cover is removed, disconnect the four ribbon cables and the two wires attached to the motherboard.

Once the motherboard cover is removed, disconnect the four ribbon cables and the two wires attached to the motherboard.

Step 7

  • Using the Phillips #00 screwdriver, remove the single 0.4 mm black screw in the center of the motherboard.
  • Remove the motherboard from the device.

Using the Phillips #00 screwdriver, remove the single 0.4 mm black screw in the center of the motherboard.

Remove the motherboard from the device.

Step 8

              Speaker
  • Use the spudger to remove the speaker from the top of the phone.

Use the spudger to remove the speaker from the top of the phone.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    curt caudle

Member since: 02/15/2021

277 Reputation

                                      3 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       The Citadel Military College of South Carolina, Team S1-G1, Eggleston Spring 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team S1-G1, Eggleston Spring 2021 



                    CMCSC-EGGLESTON-S21S1G1                     


                                            3 Members                     


                                            4 Guides authored