Difficulty
Moderate
Steps
14
Time Required
40 minutes
Sections
3
- Display
- 8 steps
- Fingerprint Sensor
- 4 steps
- Bottom Speaker
- 2 steps
Flags
0
BackMotorola Moto G5s Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display
- Power off the phone before you begin.
- Bring the heat gun one to two inches from the edges of the display to melt the display adhesive.
- Spend equal amounts of time applying heat around the entire edge of the phone.
Power off the phone before you begin.
Bring the heat gun one to two inches from the edges of the display to melt the display adhesive.
Spend equal amounts of time applying heat around the entire edge of the phone.
1024
Step 2
- Attach the suction cup to the display slightly to the left of center.
- Exert a moderate force to pull on the suction cup. The display will come loose.
Attach the suction cup to the display slightly to the left of center.
Exert a moderate force to pull on the suction cup. The display will come loose.
Step 3
- Insert the opening tool inside the loosened edge.
- Gradually work the opening tool around the edge of the entire screen to cut through the adhesive.
- Do not wedge the opening tool too far beneath the screen. Using too much force can result in torn connector cables.
Insert the opening tool inside the loosened edge.
Gradually work the opening tool around the edge of the entire screen to cut through the adhesive.
Do not wedge the opening tool too far beneath the screen. Using too much force can result in torn connector cables.
Step 4
- The display should now be entirely loose, attached only by the connectors at the top of the device and the fingerprint sensor connector at the bottom of the device.
- Press down on the fingerprint sensor with the display slightly raised to disconnect it from the display.
- If the fingerprint sensor does not come loose, use the heat gun to loosen its adhesive.
The display should now be entirely loose, attached only by the connectors at the top of the device and the fingerprint sensor connector at the bottom of the device.
Press down on the fingerprint sensor with the display slightly raised to disconnect it from the display.
If the fingerprint sensor does not come loose, use the heat gun to loosen its adhesive.
Step 5
- The cables at the top of the device are fragile. If you are using this guide as a prerequisite for replacing another part, be careful not to tear the cables while lifting the screen.
- Remove the one 5mm Torx-5 screw located by the connector cables in the top right corner of the device.
The cables at the top of the device are fragile. If you are using this guide as a prerequisite for replacing another part, be careful not to tear the cables while lifting the screen.
Remove the one 5mm Torx-5 screw located by the connector cables in the top right corner of the device.
Step 6
- Grab the unscrewed metal plate with your blunt tweezers.
- Slide the metal plate to the left and then out to remove it.
- Removing the plate will expose the display assembly’s connection to the phone’s motherboard.
Grab the unscrewed metal plate with your blunt tweezers.
Slide the metal plate to the left and then out to remove it.
Removing the plate will expose the display assembly’s connection to the phone’s motherboard.
Step 7
- Disengage the two cable connectors by gently prying beneath the edge of the connector with the opening tool.
Disengage the two cable connectors by gently prying beneath the edge of the connector with the opening tool.
Step 8
- Lift up the detached right connector from its housing using blunt tweezers.
- The housing has light adhesive underneath it. Use a small amount of force to remove the connector from the housing.
Lift up the detached right connector from its housing using blunt tweezers.
The housing has light adhesive underneath it. Use a small amount of force to remove the connector from the housing.
Step 9
Fingerprint Sensor
- Remove the nine black 5mm Torx-5 screws.
- Remove the seven silver 5mm Torx-5 screws.
Remove the nine black 5mm Torx-5 screws.
Remove the seven silver 5mm Torx-5 screws.
Step 10
- Remove the metal cover by prying underneath it with the opening tool.
Remove the metal cover by prying underneath it with the opening tool.
Step 11
- Grab ahold of the fingerprint sensor and push it through the opening in the metal cover.
Grab ahold of the fingerprint sensor and push it through the opening in the metal cover.
Step 12
- Remove the fingerprint connector by gently prying underneath the connector with the opening tool.
Remove the fingerprint connector by gently prying underneath the connector with the opening tool.
Step 13
Bottom Speaker
- Remove the one silver 5mm Torx-5 screw.
Remove the one silver 5mm Torx-5 screw.
Step 14
- Pry underneath the bottom-speaker using a spudger.
- Grab and remove the bottom-speaker using your fingers or tweezers.
Pry underneath the bottom-speaker using a spudger.
Grab and remove the bottom-speaker using your fingers or tweezers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Kevin George
Member since: 10/08/2018
982 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team S4-G5, White Fall 2018
Member of Cal Poly, Team S4-G5, White Fall 2018
CPSU-WHITE-F18S4G5
4 Members
5 Guides authored