Difficulty

Moderate

Steps

13

Time Required

                          15 minutes

Sections

5

  • Back Cover
  • 4 steps
  • Battery
  • 2 steps
  • Rear Facing Camera
  • 3 steps
  • Motherboard
  • 3 steps
  • Front Camera
  • 1 step

Flags

0

  • BackMotorola Moto G5

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Insert your fingernail or the flat end of a spudger into the notch on the bottom edge of the phone near the charging port.
  • Pry with your fingernail or twist the spudger to release the back cover from the phone.

Insert your fingernail or the flat end of a spudger into the notch on the bottom edge of the phone near the charging port.

Pry with your fingernail or twist the spudger to release the back cover from the phone.

1024

Step 2

  • Insert the flat end of a spudger into the seam and slide it along the bottom edge to release the clips holding the back cover to the phone.

Insert the flat end of a spudger into the seam and slide it along the bottom edge to release the clips holding the back cover to the phone.

Step 3

  • Continue sliding the flat end of the spudger along the seam for the remaining sides of the phone.

Continue sliding the flat end of the spudger along the seam for the remaining sides of the phone.

Step 4

  • Lift the back cover and remove it from the phone.
  • To reinstall the back cover, align the cover with the phone and squeeze along the edges to snap the clips back into place.

Lift the back cover and remove it from the phone.

To reinstall the back cover, align the cover with the phone and squeeze along the edges to snap the clips back into place.

Step 5

              Battery
  • Insert your fingernail or the flat end of the spudger into the notch below the battery.
  • Pry with your fingernail or spudger until you free the battery from its recess.

Insert your fingernail or the flat end of the spudger into the notch below the battery.

Pry with your fingernail or spudger until you free the battery from its recess.

Step 6

  • Remove the battery.
  • When installing the battery, make sure the battery’s contacts line up with the three gold pins on the top right.

Remove the battery.

When installing the battery, make sure the battery’s contacts line up with the three gold pins on the top right.

Step 7

              Rear Facing Camera
  • Remove the eight (8) 4mm screws with a Phillips screwdriver.

Remove the eight (8) 4mm screws with a Phillips screwdriver.

Step 8

  • Pry the top motherboard cover off using a plastic opening tool.
  • When prying it open, make sure to pry it around evenly so that the cover will not snap. This will require some force.

Pry the top motherboard cover off using a plastic opening tool.

When prying it open, make sure to pry it around evenly so that the cover will not snap. This will require some force.

Step 9

  • Disconnect the marked connector with a pair of tweezers and remove the camera piece.

Disconnect the marked connector with a pair of tweezers and remove the camera piece.

Step 10

              Motherboard
  • Remove the two 4mm screws shown in the picture using a Phillips #00 screwdriver.

Remove the two 4mm screws shown in the picture using a Phillips #00 screwdriver.

Step 11

  • Lift the motherboard up from the top of the phone.

Lift the motherboard up from the top of the phone.

Step 12

  • Unplug the back connector from the motherboard using tweezers.

Unplug the back connector from the motherboard using tweezers.

Step 13

              Front Camera
  • Grab the connector with the tweezers and gently unplug the front camera from the motherboard.

Grab the connector with the tweezers and gently unplug the front camera from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 5 other contributors 


                    Enosh Reeder

Member since: 01/24/2018

195 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S2-G3, Livingston Winter 2018                        

                                                  Member of Cal Poly, Team S2-G3, Livingston Winter 2018 



                    CPSU-LIVINGSTON-W18S2G3                     


                                            4 Members                     


                                            16 Guides authored