Featured
Featured Guide
Difficulty
Moderate
Steps
8
Time Required
30 - 45 minutes
Sections
1
- Back Cover
- 8 steps
Flags
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackMotorola Moto G Stylus (2022)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Heat the edge
- Discharge your battery to 25% or lower and power off your phone before you begin.
- Heat an iOpener and apply it to the edge of the cover with the SIM card slot for two minutes.
- A hair dryer or heat gun may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
Discharge your battery to 25% or lower and power off your phone before you begin.
Heat an iOpener and apply it to the edge of the cover with the SIM card slot for two minutes.
A hair dryer or heat gun may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
1024
Step 2
Insert an opening pick
- Apply a suction cup to the back cover, as close to the center of the right edge as possible.
- Pull up on the suction cup with strong, steady force to create a gap between the cover and the frame.
- Insert an opening pick into the gap.
Apply a suction cup to the back cover, as close to the center of the right edge as possible.
Pull up on the suction cup with strong, steady force to create a gap between the cover and the frame.
Insert an opening pick into the gap.
Step 3
Slice the right adhesive
- Slide your opening pick back and forth along the right edge to slice through the adhesive.
- Leave the pick in at the bottom right corner to prevent the adhesive from resealing.
Slide your opening pick back and forth along the right edge to slice through the adhesive.
Leave the pick in at the bottom right corner to prevent the adhesive from resealing.
Step 4
Slice the bottom adhesive
- Insert and slide a second opening pick to the bottom left corner to slice through the adhesive.
- Leave the pick inserted to prevent the bottom edge from resealing.
Insert and slide a second opening pick to the bottom left corner to slice through the adhesive.
Leave the pick inserted to prevent the bottom edge from resealing.
Step 5
Slice the left adhesive
- Insert and slide a third opening pick to the top left corner to slice the left adhesive.
- Avoid slicing under the camera bezel. It’s separate from the back cover and will be removed later.
- Leave the pick inserted to prevent the left edge from resealing.
Insert and slide a third opening pick to the top left corner to slice the left adhesive.
Avoid slicing under the camera bezel. It’s separate from the back cover and will be removed later.
Leave the pick inserted to prevent the left edge from resealing.
Step 6
Slice the top adhesive
- Slide your pick to the top right corner to slice the top adhesive.
Slide your pick to the top right corner to slice the top adhesive.
Step 7
Slice around the camera bezel
- Slide an opening pick between the camera bezel and the back cover.
- The back cover’s adhesive is particularly strong around the camera bezel.
- Slide the opening pick around the camera bezel to separate the back cover from the frame.
Slide an opening pick between the camera bezel and the back cover.
The back cover’s adhesive is particularly strong around the camera bezel.
Slide the opening pick around the camera bezel to separate the back cover from the frame.
Step 8
Remove the back cover
- Grab and remove the back cover.
- If your back cover is still sticking to the frame, slide the pick around the edges of the phone to slice through any remaining adhesive.
- Reassembly notes:
- To adhere the back cover with custom-cut adhesives, follow this guide.
- To adhere the back cover with tape, follow this guide.
Grab and remove the back cover.
If your back cover is still sticking to the frame, slide the pick around the edges of the phone to slice through any remaining adhesive.
Reassembly notes:
To adhere the back cover with custom-cut adhesives, follow this guide.
To adhere the back cover with tape, follow this guide.
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Clay Eickemeyer
Member since: 09/19/2022
14,946 Reputation
125 Guides authored
Badges:
27
+24 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,772 Guides authored