Difficulty

Moderate

Steps

14

Time Required

                          45 minutes - 1 hour

Sections

4

  • Back Cover
  • 6 steps
  • Motherboard Cover
  • 4 steps
  • Battery Disconnect
  • 1 step
  • Loudspeaker
  • 3 steps

Flags

0

  • BackMotorola Moto G Play (2021)

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Heat the left edge
  • Discharge your battery to 25% or lower and power off your phone before you begin.
  • Heat an iOpener and apply it to the left edge of the cover for two minutes.
  • A hair dryer or heat gun may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Discharge your battery to 25% or lower and power off your phone before you begin.

Heat an iOpener and apply it to the left edge of the cover for two minutes.

A hair dryer or heat gun may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

1024

Step 2

              Insert an opening pick
  • Apply a suction cup to the back cover, as close to the center of the left edge as possible.
  • Pull up on the suction cup with strong, steady force to create a gap between the cover and the frame.
  • Insert an opening pick into the gap.

Apply a suction cup to the back cover, as close to the center of the left edge as possible.

Pull up on the suction cup with strong, steady force to create a gap between the cover and the frame.

Insert an opening pick into the gap.

Step 3

              Slice the right adhesive
  • Slide your opening pick back and forth along the left edge to slice through the adhesive.
  • Leave the pick in at the bottom left corner to prevent the adhesive from resealing.

Slide your opening pick back and forth along the left edge to slice through the adhesive.

Leave the pick in at the bottom left corner to prevent the adhesive from resealing.

Step 4

              Slice the bottom adhesive
  • Insert and slide a second opening pick to the bottom right corner to slice through the adhesive.
  • Leave the pick inserted to prevent the bottom edge from resealing.
  • Repeat this process for the right and top edges of the cover.

Insert and slide a second opening pick to the bottom right corner to slice through the adhesive.

Leave the pick inserted to prevent the bottom edge from resealing.

Repeat this process for the right and top edges of the cover.

Step 5

              Dislodge the fingerprint reader
  • The fingerprint reader is connected to the motherboard by a fragile cable. You must free it before pulling the cover off.
  • Grab and lift the bottom edge of the cover.
  • As you lift the back cover, press and unstick the fingerprint reader from it.

The fingerprint reader is connected to the motherboard by a fragile cable. You must free it before pulling the cover off.

Grab and lift the bottom edge of the cover.

As you lift the back cover, press and unstick the fingerprint reader from it.

Step 6

              Remove the back cover
  • Grab and remove the back cover.
  • If your back cover is still sticking to the frame, slide the pick around the edges of the phone to slice through any remaining adhesive.
  • Reassembly notes:
  • This is a good point to test your phone before sealing it up. Follow this guide to perform a hardware test. Be sure to power your phone back down completely before you continue working.
  • To adhere the back cover with custom-cut adhesives, follow this guide.
  • To adhere the back cover with tape, follow this guide.

Grab and remove the back cover.

If your back cover is still sticking to the frame, slide the pick around the edges of the phone to slice through any remaining adhesive.

Reassembly notes:

This is a good point to test your phone before sealing it up. Follow this guide to perform a hardware test. Be sure to power your phone back down completely before you continue working.

To adhere the back cover with custom-cut adhesives, follow this guide.

To adhere the back cover with tape, follow this guide.

Step 7

              Reposition the fingerprint reader
  • Flip the fingerprint reader to the left, away from the phone.
  • Don’t fold or sharply bend the ribbon cable.

Flip the fingerprint reader to the left, away from the phone.

Don’t fold or sharply bend the ribbon cable.

Step 8

              Unfasten the motherboard cover
  • Use your Phillips screwdriver to remove the twelve 3.9 mm-long screws securing the motherboard cover.

Use your Phillips screwdriver to remove the twelve 3.9 mm-long screws securing the motherboard cover.

Step 9

              Pry the motherboard cover
  • Insert the pointed end of a spudger between the bottom right corner of the motherboard cover and the frame.
  • Pry the cover upward until you can grab it with your fingers.

Insert the pointed end of a spudger between the bottom right corner of the motherboard cover and the frame.

Pry the cover upward until you can grab it with your fingers.

Step 10

              Remove the motherboard cover
  • Grab the bottom edge of the motherboard cover and remove it from the frame.

Grab the bottom edge of the motherboard cover and remove it from the frame.

Step 11

              Disconnect the battery
  • Use the pointed end of your spudger to pry and disconnect the battery’s press connector.
  • To re-attach press connectors, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don’t press down on the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

Use the pointed end of your spudger to pry and disconnect the battery’s press connector.

To re-attach press connectors, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don’t press down on the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

Step 12

              Unfasten the loudspeaker
  • Use your Phillips screwdriver to remove the eight 3.8 mm-long screws securing the loudspeaker.

Use your Phillips screwdriver to remove the eight 3.8 mm-long screws securing the loudspeaker.

Step 13

              Pry the loudspeaker
  • Insert your spudger between the top right corner of the loudspeaker and the frame.
  • Pry up to release the loudspeaker.

Insert your spudger between the top right corner of the loudspeaker and the frame.

Pry up to release the loudspeaker.

Step 14

              Remove the loudspeaker
  • Grab the loudspeaker with your fingers and remove it.

Grab the loudspeaker with your fingers and remove it.

Compare your new replacement part to the original part—be sure to transfer remaining components and remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                    Clay Eickemeyer

Member since: 09/19/2022

14,946 Reputation

                                      125 Guides authored                  



                       Badges:
                       27







                                                        +24 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored