Motorola Moto G 2Nd Generation Front Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 25 minutes

Sections

Battery
5 steps
Motherboard
3 steps
Front Camera
1 step

Flags

BackMotorola Moto G (2nd Generation)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure your Moto G is turned off and that any SIM or SD cards are removed before beginning disassembly.
Starting at the USB port on the bottom, remove the rear cover by prying it off with your finger.
Work your way down the sides to avoid cracking the rear cover.

Make sure your Moto G is turned off and that any SIM or SD cards are removed before beginning disassembly.

Starting at the USB port on the bottom, remove the rear cover by prying it off with your finger.

Work your way down the sides to avoid cracking the rear cover.

1024

Step 2

Remove the eight 4.2 mm screws at the top and bottom of the phone using a T5 Torx screwdriver.
Using the same screwdriver, remove the six 3.2 mm screws on the sides.
Remove the next layer of the phone by prying it off with your fingers.

Remove the eight 4.2 mm screws at the top and bottom of the phone using a T5 Torx screwdriver.

Using the same screwdriver, remove the six 3.2 mm screws on the sides.

Remove the next layer of the phone by prying it off with your fingers.

Step 3

Using a plastic opening tool or tweezers, disconnect the SIM/SD card reader at the top of the phone.
Disconnect the battery connector by prying it off of the motherboard.
Disconnect the vibration motor by prying its connector off of the motherboard.

Using a plastic opening tool or tweezers, disconnect the SIM/SD card reader at the top of the phone.

Disconnect the battery connector by prying it off of the motherboard.

Disconnect the vibration motor by prying its connector off of the motherboard.

Step 4

Using a plastic opening tool, carefully pry off the entire SIM/SD card reader component.
Don’t worry about ripping the copper foil a little bit, it is easy to put back on.
When reassembling the device, do not attempt to smooth the foil down with your finger. Metal foil can become sharp if folded in a certain way, and you may be cut.
The battery may be removed without removing the SIM/SD card reader. Simply peel back the copper foil from the opposite end of the device, stopping just before you reach the SIM/SD card reader.

Using a plastic opening tool, carefully pry off the entire SIM/SD card reader component.

Don’t worry about ripping the copper foil a little bit, it is easy to put back on.

When reassembling the device, do not attempt to smooth the foil down with your finger. Metal foil can become sharp if folded in a certain way, and you may be cut.

The battery may be removed without removing the SIM/SD card reader. Simply peel back the copper foil from the opposite end of the device, stopping just before you reach the SIM/SD card reader.

Step 5

Peel off the two black stickers on the right side of the battery using your fingers.
Remove the battery by pulling the right side of it upwards.
The black stickers are the protruding ends of the two parallel adhesive strips which hold the battery in place. You can see the adhesive strips in the third image. Focus your effort on these regions.
If you did not remove the SIM/SD card reader in the previous step, you will need to carefully slide the battery ribbon cable out from under it once you have freed the battery from the adhesive strips.

Peel off the two black stickers on the right side of the battery using your fingers.

Remove the battery by pulling the right side of it upwards.

The black stickers are the protruding ends of the two parallel adhesive strips which hold the battery in place. You can see the adhesive strips in the third image. Focus your effort on these regions.

If you did not remove the SIM/SD card reader in the previous step, you will need to carefully slide the battery ribbon cable out from under it once you have freed the battery from the adhesive strips.

Step 6

              Motherboard

Remove LCD connector by lifting the black plastic flap.

Remove LCD connector by lifting the black plastic flap.

Step 7

Using a T5 Torx screwdriver, unscrew the three 2.2 mm screws holding the motherboard in place.

Using a T5 Torx screwdriver, unscrew the three 2.2 mm screws holding the motherboard in place.

Step 8

Carefully remove the motherboard.

Carefully remove the motherboard.

Step 9

              Front Camera

Use the prying tweezers to remove the front facing camera.

Use the prying tweezers to remove the front facing camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 3 other contributors

                    stanley rosky

Member since: 10/01/2015

713 Reputation

                                      2 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       Cal Poly, Team 1-19, Maness Fall 2015                        

                                                  Member of Cal Poly, Team 1-19, Maness Fall 2015 



                    CPSU-MANESS-F15S1G19                     


                                            4 Members                     


                                            15 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team