Motorola Moto E6 Screen Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          40 - 55 minutes            

Sections

5

• Back Cover
• 1 step
• Battery
• 1 step
• Motherboard
• 4 steps
• Charging Dock
• 4 steps
• Screen Assembly
• 1 step

Flags

1

Needs More Images

A few more images would make this guide’s procedures crystal clear.

• BackMotorola Moto E6

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Back Cover               

• Begin by prying open the bottom right of the device using the plastic opening tool.
• Work your way around the edge of the device, slowly prying open the casing until it pops off.

Begin by prying open the bottom right of the device using the plastic opening tool.

Work your way around the edge of the device, slowly prying open the casing until it pops off.

1024

Step 2

              Battery               

• Use the opening tool on the divot located below the battery to pop it out.

Use the opening tool on the divot located below the battery to pop it out.

Step 3

              Motherboard               

• Remove the eleven 3.8 mm T4 Torx screws located above the battery compartment.

Remove the eleven 3.8 mm T4 Torx screws located above the battery compartment.

Step 4

• Use the plastic opening tools to pry open the piece located at the top of the device.
• Start by prying open the side of the compartment and work your way towards the camera module, prying open the compartment as you go.
• Pop off the piece above the battery compartment.

Use the plastic opening tools to pry open the piece located at the top of the device.

Start by prying open the side of the compartment and work your way towards the camera module, prying open the compartment as you go.

Pop off the piece above the battery compartment.

Step 5

• Remove the two 1.1 mm T4 Torx screws from the bottom left and top right sides of the motherboard.

Remove the two 1.1 mm T4 Torx screws from the bottom left and top right sides of the motherboard.

Step 6

• Remove the two press fit cables at the bottom of the motherboard with the plastic opening tool.
• Remove the coaxial cable using the plastic opening tool.
• After removing the cables, remove the motherboard from the phone by hand.

Remove the two press fit cables at the bottom of the motherboard with the plastic opening tool.

Remove the coaxial cable using the plastic opening tool.

After removing the cables, remove the motherboard from the phone by hand.

Step 7

              Charging Dock               

• Remove the seven 3.8 mm T4 screws on the piece located below the battery compartment.

Remove the seven 3.8 mm T4 screws on the piece located below the battery compartment.

Step 8

• Begin prying off the bottom piece with the opening tools on the divot located at the bottom left.
• Work your way around the piece until it pops off.

Begin prying off the bottom piece with the opening tools on the divot located at the bottom left.

Work your way around the piece until it pops off.

Step 9

• Remove the press fit cable at the top of the charging dock with the plastic opening tool.
• Remove the coaxial cable using the plastic opening tool.

Remove the press fit cable at the top of the charging dock with the plastic opening tool.

Remove the coaxial cable using the plastic opening tool.

Step 10

• Remove the two 1.1 mm T4 Torx screws on the bottom right and top left sides of the charging dock.
• Remove the charging dock by hand.

Remove the two 1.1 mm T4 Torx screws on the bottom right and top left sides of the charging dock.

Remove the charging dock by hand.

Step 11

              Screen Assembly               

• After removing the motherboard and the charging dock, the screen assembly can be replaced.

After removing the motherboard and the charging dock, the screen assembly can be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Ty Duben                     

Member since: 09/16/2020

136 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       The Citadel Military College of South Carolina, Team S2-G16, Eggleston Fall 2020                        

                                                  Member of The Citadel Military College of South Carolina, Team S2-G16, Eggleston Fall 2020 



                    CMCSC-EGGLESTON-F20S2G16                     


                                            3 Members                     


                                            5 Guides authored                     

Aksel Barnes - Mar 12, 2021

Reply

Pro Tip.

The OEM parts for this do not include the flex that connects the Sub to main PBA, nor the earspeaker, nor the buttons or Vibration motor, so all of those will need to be moved over if you are utilizing OEM original components.

Bobby Browning - Aug 22, 2021

Reply

you get me right to the point where i can get to the screen. now, how i do iget it off? put the new one on???

Thaddeus Ervin - Jul 22, 2022

Use heat on the display to loosen the adhesive. Then you can separate the display and put in the new one.