Difficulty

Moderate

Steps

19

Time Required

                          20 - 40 minutes

Sections

3

  • Back Cover
  • 5 steps
  • Motherboard Cover
  • 12 steps
  • Rear Cameras
  • 2 steps

Flags

0

  • BackMotorola Moto E6 Plus

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Unclip the back cover
  • Use an opening tool or your fingernail to pry the back cover away from the frame using the notch at the bottom right corner.

Use an opening tool or your fingernail to pry the back cover away from the frame using the notch at the bottom right corner.

1024

Step 2

              Unclip the right edge
  • Use an opening tool or your fingernail to release the clips on the right edge by sliding up and around the top right corner.

Use an opening tool or your fingernail to release the clips on the right edge by sliding up and around the top right corner.

Step 3

              Unclip the top edge
  • Continue to slide the opening tool or your fingernail across the top edge to release the clips securing the back cover to the frame.

Continue to slide the opening tool or your fingernail across the top edge to release the clips securing the back cover to the frame.

Step 4

              Unclip the left edge
  • Continue to slide the opening tool or your fingernail down the left edge to release the clips.

Continue to slide the opening tool or your fingernail down the left edge to release the clips.

Step 5

              Remove the back cover
  • Remove the back cover.

Remove the back cover.

Step 6

              Remove the SIM and SD cards
  • Use a spudger or your fingernail to remove the Micro SD card, the Micro SIM card, and the Nano SIM card.

Use a spudger or your fingernail to remove the Micro SD card, the Micro SIM card, and the Nano SIM card.

Step 7

              Remove the white sticker
  • Use a pair of tweezers to remove the sticker covering the screw below the audio jack port.

Use a pair of tweezers to remove the sticker covering the screw below the audio jack port.

Step 8

              Remove the screws
  • Use a Torx T3 driver to remove the five 3.6 mm-long screws securing the motherboard cover to the frame.
  • Use a Phillips screwdriver to remove the two 3.1 mm-long screws.

Use a Torx T3 driver to remove the five 3.6 mm-long screws securing the motherboard cover to the frame.

Use a Phillips screwdriver to remove the two 3.1 mm-long screws.

Step 9

              Peel back the button sticker
  • Use a pair of tweezers to peel back the sticker covering the volume buttons.

Use a pair of tweezers to peel back the sticker covering the volume buttons.

Step 10

              Pry up the motherboard cover
  • Use an opening tool to release the clip to the left of the motherboard flex cable.

Use an opening tool to release the clip to the left of the motherboard flex cable.

Step 11

  • Insert a spudger along the left edge of the motherboard cover to loosen the clips.

Insert a spudger along the left edge of the motherboard cover to loosen the clips.

Step 12

              Pry up the motherboard cover
  • Use an opening tool to release the clip next to the rear cameras.

Use an opening tool to release the clip next to the rear cameras.

Step 13

  • Use a pair of tweezers to peel off the sticker on the top edge of the motherboard cover.

Use a pair of tweezers to peel off the sticker on the top edge of the motherboard cover.

Step 14

              Pry up the motherboard cover
  • Use a spudger to lift up the left edge of the motherboard cover to loosen the clips.

Use a spudger to lift up the left edge of the motherboard cover to loosen the clips.

Step 15

              Dislodge the fingerprint sensor
  • Use a spudger to push and dislodge the fingerprint sensor off of the motherboard cover.
  • The fingerprint sensor is secured to the underside of the motherboard cover with some light adhesive.

Use a spudger to push and dislodge the fingerprint sensor off of the motherboard cover.

The fingerprint sensor is secured to the underside of the motherboard cover with some light adhesive.

Step 16

              Remove the motherboard cover
  • Use your fingers to twist the motherboard cover counterclockwise to release the clips securing the motherboard cover.

Use your fingers to twist the motherboard cover counterclockwise to release the clips securing the motherboard cover.

Step 17

  • Remove the motherboard cover.

Remove the motherboard cover.

Step 18

              Remove the rear cameras
  • Use the flat end of a spudger to disconnect the rear camera from the motherboard by lifting straight up on the press connector.
  • Remove the rear camera.

Use the flat end of a spudger to disconnect the rear camera from the motherboard by lifting straight up on the press connector.

Remove the rear camera.

Step 19

  • Use the flat end of a spudger to disconnect the depth information camera from the motherboard by lifting straight up on the press connector.
  • Remove the depth information camera.

Use the flat end of a spudger to disconnect the depth information camera from the motherboard by lifting straight up on the press connector.

Remove the depth information camera.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Motorola Moto E6 Plus Answers community for help.

Cancel: I did not complete this guide.

Author

                    Robert Boyd

Member since: 02/01/2021

21,303 Reputation

                                      92 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges