Difficulty
Moderate
Steps
10
Time Required
10 minutes
Sections
3
- Back Cover
- 1 step
- Circuit Board Covers
- 4 steps
- Front Facing Camera
- 5 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackMotorola Moto E6 Play
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Run the halberd spudger along the edges of the device. The back cover should easily pop off.
- Gently remove the back cover. Do not pull hard, as it is still connected to the fingerprint scanner inside the phone.
Run the halberd spudger along the edges of the device. The back cover should easily pop off.
Gently remove the back cover. Do not pull hard, as it is still connected to the fingerprint scanner inside the phone.
1024
Step 2
Circuit Board Covers
- To remove the cover on the motherboard, remove the 10 silver 3.90 mm Phillips screws attaching the cover to the board using the Phillips #0 screwdriver.
- One of these ten screws is covered by black tape located at the bottom left corner of the black cover. Peel back the black tape to access this screw.
To remove the cover on the motherboard, remove the 10 silver 3.90 mm Phillips screws attaching the cover to the board using the Phillips #0 screwdriver.
One of these ten screws is covered by black tape located at the bottom left corner of the black cover. Peel back the black tape to access this screw.
Step 3
- With the angled tweezers, remove the black cover to reveal the motherboard underneath.
- Remove the black piece cover with caution to avoid puncturing the motherboard with the tweezers.
With the angled tweezers, remove the black cover to reveal the motherboard underneath.
Remove the black piece cover with caution to avoid puncturing the motherboard with the tweezers.
Step 4
- The bottom plastic piece covering the daughterboard can be seen by peeling back the tape covering the bottom section of the phone below the battery.
- To remove the cover, unscrew the six black 3.45 mm Phillips screws holding the cover in place using the Phillips #0 screwdriver.
The bottom plastic piece covering the daughterboard can be seen by peeling back the tape covering the bottom section of the phone below the battery.
To remove the cover, unscrew the six black 3.45 mm Phillips screws holding the cover in place using the Phillips #0 screwdriver.
Step 5
- Remove the black cover piece using the angled tweezers.
Remove the black cover piece using the angled tweezers.
Step 6
Front Facing Camera
- Use the angled tweezers to pry off the metal head of the connecting piece from the main motherboard assembly.
Use the angled tweezers to pry off the metal head of the connecting piece from the main motherboard assembly.
Step 7
- Using the angled tweezers, detach the two connectors from the motherboard by pulling the metallic heads up and away from the phone.
Using the angled tweezers, detach the two connectors from the motherboard by pulling the metallic heads up and away from the phone.
Step 8
- Use the angled tweezers to flip the black plastic piece from flat to upright.
- This will allow you to separate the mini connector from the motherboard later.
Use the angled tweezers to flip the black plastic piece from flat to upright.
This will allow you to separate the mini connector from the motherboard later.
Step 9
- Disconnect the rod connected to the motherboard using the angled tweezers.
- Gently pull the small metal head of the rod up vertically perpendicular from the motherboard, with caution to avoid puncturing the board with the tweezers.
- Finally, remove the motherboard.
Disconnect the rod connected to the motherboard using the angled tweezers.
Gently pull the small metal head of the rod up vertically perpendicular from the motherboard, with caution to avoid puncturing the board with the tweezers.
Finally, remove the motherboard.
Step 10
- Flip the motherboard over to see the back. (The side that does not have the ‘a’ mark on it.)
- Using the angled tweezers, lift the tab at the bottom of the camera piece and remove the front facing camera from the circuit board.
Flip the motherboard over to see the back. (The side that does not have the ‘a’ mark on it.)
Using the angled tweezers, lift the tab at the bottom of the camera piece and remove the front facing camera from the circuit board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Charlie Priebe
Member since: 02/10/2020
803 Reputation
5 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team S22-G4, Regan Winter 2020
Member of Cal Poly, Team S22-G4, Regan Winter 2020
CPSU-REGAN-W20S22G4
4 Members
14 Guides authored