Motorola Moto E6 Play Back Facing Camera Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          10 minutes            

Sections

3

• Back Cover
• 1 step
• Circuit Board Covers
• 4 steps
• Back Facing Camera
• 5 steps

Flags

0

• BackMotorola Moto E6 Play

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

If you are experiencing the ‘Camera Busy’ error, click here for troubleshooting solutions. However, if you are experiencing other issues with the back camera, or the troubleshooting guides do not solve the problem, you may need to replace the camera.

What you need

Step 1

              Back Cover               

• Run the halberd spudger along the edges of the device. The back cover should easily pop off.
• Gently remove the back cover. Do not pull hard, as it is still connected to the fingerprint scanner inside the phone.

Run the halberd spudger along the edges of the device. The back cover should easily pop off.

Gently remove the back cover. Do not pull hard, as it is still connected to the fingerprint scanner inside the phone.

1024

Step 2

              Circuit Board Covers               

• To remove the cover on the motherboard, remove the 10 silver 3.90 mm Phillips screws attaching the cover to the board using the Phillips #0 screwdriver.
• One of these ten screws is covered by black tape located at the bottom left corner of the black cover. Peel back the black tape to access this screw.

To remove the cover on the motherboard, remove the 10 silver 3.90 mm Phillips screws attaching the cover to the board using the Phillips #0 screwdriver.

One of these ten screws is covered by black tape located at the bottom left corner of the black cover. Peel back the black tape to access this screw.

Step 3

• With the angled tweezers, remove the black cover to reveal the motherboard underneath.
• Remove the black piece cover with caution to avoid puncturing the motherboard with the tweezers.

With the angled tweezers, remove the black cover to reveal the motherboard underneath.

Remove the black piece cover with caution to avoid puncturing the motherboard with the tweezers.

Step 4

• The bottom plastic piece covering the daughterboard can be seen by peeling back the tape covering the bottom section of the phone below the battery.
• To remove the cover, unscrew the six black 3.45 mm Phillips screws holding the cover in place using the Phillips #0 screwdriver.

The bottom plastic piece covering the daughterboard can be seen by peeling back the tape covering the bottom section of the phone below the battery.

To remove the cover, unscrew the six black 3.45 mm Phillips screws holding the cover in place using the Phillips #0 screwdriver.

Step 5

• Remove the black cover piece using the angled tweezers.

Remove the black cover piece using the angled tweezers.

Step 6

              Back Facing Camera               

• Use the angled tweezers to pry off the metal head of the connecting piece from the main motherboard assembly.

Use the angled tweezers to pry off the metal head of the connecting piece from the main motherboard assembly.

Step 7

• Using the angled tweezers, detach the two connectors from the motherboard by pulling the metallic head up and away from the phone.

Using the angled tweezers, detach the two connectors from the motherboard by pulling the metallic head up and away from the phone.

Step 8

• Use the angled tweezers to flip the black plastic piece from flat to upright.
• This will allow you to separate the mini connector from the motherboard later.

Use the angled tweezers to flip the black plastic piece from flat to upright.

This will allow you to separate the mini connector from the motherboard later.

Step 9

• Disconnect the rod connected to the motherboard using the angled tweezers.
• Gently pull the small metal head of the vertically perpendicular from the motherboard with caution to avoid puncturing the board with the tweezers.

Disconnect the rod connected to the motherboard using the angled tweezers.

Gently pull the small metal head of the vertically perpendicular from the motherboard with caution to avoid puncturing the board with the tweezers.

Step 10

• Using the angled tweezers, gently lift and pull the tab at the bottom of the camera to remove the back facing camera from the circuit board.

Using the angled tweezers, gently lift and pull the tab at the bottom of the camera to remove the back facing camera from the circuit board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Charlie Priebe                     

Member since: 02/10/2020

803 Reputation

                                      5 Guides authored                  



                       Badges:
                       13





                                                        +10 more badges                           

Team

                       Cal Poly, Team S22-G4, Regan Winter 2020                        

                                                  Member of Cal Poly, Team S22-G4, Regan Winter 2020 



                    CPSU-REGAN-W20S22G4                     


                                            4 Members                     


                                            14 Guides authored