Difficulty
Moderate
Steps
17
Time Required
25 - 35 minutes
Sections
5
- Back Cover
- 2 steps
- Battery
- 1 step
- Motherboard Cover
- 4 steps
- Motherboard Assembly
- 8 steps
- Earpiece Speaker
- 2 steps
Flags
0
BackMotorola Moto E4 (XT1762)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
You’ll need replacement adhesive to reattach components when reassembling the device.
What you need
Step 1
Back Cover
- Power off your phone before beginning disassembly.
- Insert a fingernail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover.
- Move to the bottom left corner to pry the phone out of the back cover.
Power off your phone before beginning disassembly.
Insert a fingernail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover.
Move to the bottom left corner to pry the phone out of the back cover.
1024
Step 2
- Lift the phone out of the back cover.
Lift the phone out of the back cover.
Step 3
Battery
- Use a fingernail or spudger to pry at the notch at the bottom end of the battery.
- Lever the battery out of its recess and remove it.
Use a fingernail or spudger to pry at the notch at the bottom end of the battery.
Lever the battery out of its recess and remove it.
Step 4
Motherboard Cover
- Remove the seven 3.3 mm Phillips #00 screws.
Remove the seven 3.3 mm Phillips #00 screws.
Step 5
- Insert an opening pick between the cover and the motherboard at the bottom right corner.
- Slide the opening pick upwards to open the plastic clips.
Insert an opening pick between the cover and the motherboard at the bottom right corner.
Slide the opening pick upwards to open the plastic clips.
Step 6
- Insert an opening pick between the cover and the motherboard at the bottom left corner.
- Slide the opening pick upwards to open the plastic clips.
- Pry up the motherboard cover by twisting the opening pick.
Insert an opening pick between the cover and the motherboard at the bottom left corner.
Pry up the motherboard cover by twisting the opening pick.
Step 7
- Remove the motherboard cover.
Remove the motherboard cover.
Step 8
Motherboard Assembly
- Use a pair of tweezers to peel off the yellow tape of the ZIF connector located on the left of the motherboard.
Use a pair of tweezers to peel off the yellow tape of the ZIF connector located on the left of the motherboard.
Step 9
- Use the edge of a spudger to open the black flap of the ZIF connector.
Use the edge of a spudger to open the black flap of the ZIF connector.
Step 10
- Slide the volume button flex cable out of the ZIF connector to disconnect it.
Slide the volume button flex cable out of the ZIF connector to disconnect it.
Step 11
- Use a pair of tweezers to pry up and disconnect the antenna cable located on the left of the motherboard.
- Fold the antenna cable out of the way.
Use a pair of tweezers to pry up and disconnect the antenna cable located on the left of the motherboard.
Fold the antenna cable out of the way.
Step 12
- Use the edge of a spudger to pry up and disconnect the display flex cable located on the bottom left of the motherboard.
Use the edge of a spudger to pry up and disconnect the display flex cable located on the bottom left of the motherboard.
Step 13
- Remove the two 2.9 mm long Phillips #00 screws securing the motherboard.
Remove the two 2.9 mm long Phillips #00 screws securing the motherboard.
Step 14
- Don’t try to remove the motherboard all the way yet. The interconnect flex cable is still connected to its rear side.
- Use a spudger to carefully lift the motherboard from the top and fold it towards the battery compartment.
- Be careful not to damage any components underneath the motherboard.
Don’t try to remove the motherboard all the way yet. The interconnect flex cable is still connected to its rear side.
Use a spudger to carefully lift the motherboard from the top and fold it towards the battery compartment.
Be careful not to damage any components underneath the motherboard.
Step 15
- Use the edge of a spudger to disconnect the interconnect cable from the motherboard.
- Remove the motherboard.
Use the edge of a spudger to disconnect the interconnect cable from the motherboard.
Remove the motherboard.
Step 16
Earpiece Speaker
- Apply a heated iOpener for about one minute to the upper part of the display to loosen the adhesive beneath the earpiece speaker.
Apply a heated iOpener for about one minute to the upper part of the display to loosen the adhesive beneath the earpiece speaker.
Step 17
- Use a pair of tweezers to lift the earpiece speaker out of its recess and remove it.
- When reassembling, be sure to properly orient the earpiece speaker such that the gold contacts are pointing away from the top edge.
Use a pair of tweezers to lift the earpiece speaker out of its recess and remove it.
When reassembling, be sure to properly orient the earpiece speaker such that the gold contacts are pointing away from the top edge.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 1 other contributor
Dominik Schnabelrauch
Member since: 11/23/2016
158,135 Reputation
649 Guides authored
Badges:
40
+37 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored