Motorola Moto E4 Plus Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 3 hours

Sections

Back Cover
2 steps
Midframe
6 steps
Motorola Moto E4 Plus Battery Disconnect
1 step
Motorola Moto E4 Plus Motherboard Assembly
6 steps
Earpiece Speaker
2 steps
Screen
11 steps

Flags

BackMotorola Moto E4 Plus (XT1771)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

While this guide is written with the XT1771 model, you can also use this guide for other Moto E4 Plus variants, such as XT1772, and XT1773.

Before disassembling your phone, discharge the battery below 25%. If your battery is swollen, do not heat your phone. Swollen batteries can be very dangerous, so wear eye protection and exercise due caution, or take it to a professional if you’re not sure how to proceed.

You’ll need replacement adhesive to reattach components when reassembling the device.

What you need

Step 1

              Remove the back cover

Power off your phone before beginning disassembly.
Insert the edge of the spudger into the notch on the bottom right corner of the phone.
Twist the spudger to start releasing the back cover from the phone.
Slide the spudger along the bottom edge to separate the back cover from the phone.

Power off your phone before beginning disassembly.

Insert the edge of the spudger into the notch on the bottom right corner of the phone.

Twist the spudger to start releasing the back cover from the phone.

Slide the spudger along the bottom edge to separate the back cover from the phone.

1024

Step 2

Lift the phone unit out of the back cover.

Lift the phone unit out of the back cover.

Step 3

              Midframe

Remove the eighteen 3.3 mm Phillips screws securing the midframe assembly.

Remove the eighteen 3.3 mm Phillips screws securing the midframe assembly.

Step 4

Remove the charging board cover.

Remove the charging board cover.

Step 5

Remove the battery cover.

Remove the battery cover.

Step 6

Insert an opening pick underneath the bottom left corner of the motherboard cover.
Slide the opening pick between the cover and the second SIM tray to release the plastic clip.

Insert an opening pick underneath the bottom left corner of the motherboard cover.

Slide the opening pick between the cover and the second SIM tray to release the plastic clip.

Step 7

Insert an opening pick underneath the bottom right corner of the motherboard cover.
Use the opening pick to pry up the motherboard cover.

Insert an opening pick underneath the bottom right corner of the motherboard cover.

Use the opening pick to pry up the motherboard cover.

Step 8

Remove the motherboard cover.

Remove the motherboard cover.

Step 9

              Battery Disconnect

Use the edge of a spudger to pry up and disconnect the battery flex cable from the motherboard.

Use the edge of a spudger to pry up and disconnect the battery flex cable from the motherboard.

Step 10

              Motherboard Assembly

Remove the two 2.9 mm Phillips screws.

Remove the two 2.9 mm Phillips screws.

Step 11

Use the edge of a spudger to pry up the flap of the ZIF connector located below the SIM slot on the left side of the motherboard.
Use a pair of tweezers to pull the power and volume button flex cable out of the ZIF connector.
To reattach ZIF connectors like this one, carefully insert the flex cable into the ZIF connector up to the marked line on the cable, and then close the locking flap.

Use the edge of a spudger to pry up the flap of the ZIF connector located below the SIM slot on the left side of the motherboard.

Use a pair of tweezers to pull the power and volume button flex cable out of the ZIF connector.

To reattach ZIF connectors like this one, carefully insert the flex cable into the ZIF connector up to the marked line on the cable, and then close the locking flap.

Step 12

Use a pair of tweezers to pry up and disconnect the antenna cable.

Use a pair of tweezers to pry up and disconnect the antenna cable.

Step 13

Use the flat end of a spudger to pry up and disconnect the interconnect flex cable.

Use the flat end of a spudger to pry up and disconnect the interconnect flex cable.

Step 14

Use the tip of a spudger or an opening pick to pry up the flap of the ZIF connector, located in the bottom right corner of the motherboard.
Use a pair of tweezers to pull the display flex cable out of the ZIF connector.

Use the tip of a spudger or an opening pick to pry up the flap of the ZIF connector, located in the bottom right corner of the motherboard.

Use a pair of tweezers to pull the display flex cable out of the ZIF connector.

Step 15

Grasp the motherboard by the top corners and remove it by lifting up and pulling it carefully out of its recess.

Grasp the motherboard by the top corners and remove it by lifting up and pulling it carefully out of its recess.

Step 16

              Earpiece Speaker

Apply a heated iOpener to the upper part of the phone for about 30 seconds to loosen the adhesive beneath the earpiece speaker.

Apply a heated iOpener to the upper part of the phone for about 30 seconds to loosen the adhesive beneath the earpiece speaker.

Step 17

When removing the earpiece speaker with a pair of tweezers, take care to grab the whole unit. The earpiece speaker can easily break in two pieces if you only pull on its upper half.
Use a pair of tweezers to lift the earpiece speaker out of its recess and remove it.
When reassembling, be sure to properly orient the earpiece speaker such that the gold contacts are pointing away from the top edge.

When removing the earpiece speaker with a pair of tweezers, take care to grab the whole unit. The earpiece speaker can easily break in two pieces if you only pull on its upper half.

Use a pair of tweezers to lift the earpiece speaker out of its recess and remove it.

When reassembling, be sure to properly orient the earpiece speaker such that the gold contacts are pointing away from the top edge.

Step 18

              Display with Frame

Use a pair of tweezers to gently peel the power and volume button unit out of its thin recess on the left side of the frame.
Remove the power and volume button unit.

Use a pair of tweezers to gently peel the power and volume button unit out of its thin recess on the left side of the frame.

Remove the power and volume button unit.

Step 19

Use a pair of tweezers to peel the ends of the two pull tabs off of the bottom edge of the battery.

Use a pair of tweezers to peel the ends of the two pull tabs off of the bottom edge of the battery.

Step 20

Pull out the left adhesive strip by steadily pulling the left tab at a flat angle.
If the adhesive strip rips, grab and twist the remaining stub around the tip of a pair of tweezers a couple of times and then continue pulling.
Repeat the same process for the right adhesive strip.

Pull out the left adhesive strip by steadily pulling the left tab at a flat angle.

If the adhesive strip rips, grab and twist the remaining stub around the tip of a pair of tweezers a couple of times and then continue pulling.

Repeat the same process for the right adhesive strip.

Step 21

Get a good grip on the battery and remove it.

Get a good grip on the battery and remove it.

Step 22

Remove the single 2.9 mm Phillips screw holding the charging board to the frame.

Remove the single 2.9 mm Phillips screw holding the charging board to the frame.

Step 23

Use a pair of tweezers to pry up and disconnect the antenna cable and remove it.

Use a pair of tweezers to pry up and disconnect the antenna cable and remove it.

Step 24

Use the edge of a spudger to pry up and disconnect the interconnect flex cable.

Use the edge of a spudger to pry up and disconnect the interconnect flex cable.

Step 25

Use the edge of a spudger to pry up and disconnect the fingerprint sensor flex cable.

Use the edge of a spudger to pry up and disconnect the fingerprint sensor flex cable.

Step 26

Insert the tip of a spudger underneath the bottom edge of the charging board and pry upwards.
Remove the charging board.

Insert the tip of a spudger underneath the bottom edge of the charging board and pry upwards.

Remove the charging board.

Step 27

Use a pair of tweezers to gently peel the interconnect flex cable from the frame and remove it.

Use a pair of tweezers to gently peel the interconnect flex cable from the frame and remove it.

Step 28

The bare screen with frame remains.
Before reassembly, check your new part for any components like gaskets, that might need to be transferred from the old one.

The bare screen with frame remains.

Before reassembly, check your new part for any components like gaskets, that might need to be transferred from the old one.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 3 other contributors

                    Dominik Schnabelrauch

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored

henri perrin - Mar 16, 2021

Bonjour cher ami

Grace a vous je me suis lancé dans le remplacement de mon ecran explosé par le passage d’un véhicule. j’ai suivi vos explications a la lettre dans le démontage et pour le remontage aussi vous n’avez pas signalé de récupérer le revêtement de cuivre, j’ai réussi de le décoller en chauffant. Tout fonctionne comme avant.

Merci de ce tuto. Félicitations.

Tobias Isakeit - May 19, 2021

Introduction#

What you need#

Team#

Introduction

What you need

Team