Difficulty

Difficult

Steps

13

Time Required

                          30 minutes - 1 hour            

Sections

2

  • Motherboard
  • 9 steps
  • Display Assembly
  • 4 steps

Flags

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

  • BackMotorola Moto E 1st Generation

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Motherboard               
  • Turn off the device before beginning.
  • To remove the back cover, start at one corner and stick the plastic opening tool under the cover and pry it away from the phone.
  • With the plastic opening tool, pry all the way around the phone while lifting up on the cover.
  • You should hear a snapping sound at each corner.

Turn off the device before beginning.

To remove the back cover, start at one corner and stick the plastic opening tool under the cover and pry it away from the phone.

With the plastic opening tool, pry all the way around the phone while lifting up on the cover.

You should hear a snapping sound at each corner.

1024

Step 2

  • Unscrew the 14- 4mm screws using a T4 Torx driver head.
  • Working on a magnet board is recommended as the screws are small and can be easily misplaced.

Unscrew the 14- 4mm screws using a T4 Torx driver head.

Working on a magnet board is recommended as the screws are small and can be easily misplaced.

Step 3

  • Using the same plastic opening tool as in step 1, once again pry up on the edges of the plastic back cover.
  • Be sure that all of the screws are out before lifting the cover. The plastic backing is fragile, and it may break.

Using the same plastic opening tool as in step 1, once again pry up on the edges of the plastic back cover.

Be sure that all of the screws are out before lifting the cover. The plastic backing is fragile, and it may break.

Step 4

  • Gently lift the back plate away, exposing the motherboard. The battery will be stuck to the back of the cover, so be careful when lifting it off.
  • Do not touch the connections to the battery in the red square on the picture.

Gently lift the back plate away, exposing the motherboard. The battery will be stuck to the back of the cover, so be careful when lifting it off.

Do not touch the connections to the battery in the red square on the picture.

Step 5

  • Gently pull up on the red and black power cable to lift the connector out of the motherboard.
  • Move the battery and cover away from the motherboard.

Gently pull up on the red and black power cable to lift the connector out of the motherboard.

Move the battery and cover away from the motherboard.

Step 6

  • Unscrew the 3- 1mm screws using the T4 torx driver head.

Unscrew the 3- 1mm screws using the T4 torx driver head.

Step 7

  • Lift up on the white plastic mount.
  • Pull the orange ribbon cable out gently.

Lift up on the white plastic mount.

Pull the orange ribbon cable out gently.

Step 8

  • Gently pull the black ribbon cable out.

Gently pull the black ribbon cable out.

Step 9

  • Using the metal spudger, pry the motherboard away from the screen assembly.

Using the metal spudger, pry the motherboard away from the screen assembly.

Step 10

              Display Assembly               
  • Use a heat gun or hairdryer to heat up the edges. This will loosen the glue so the screen can be removed.
  • The phone will be extremely hot. Avoid direct contact with metal pieces.

Use a heat gun or hairdryer to heat up the edges. This will loosen the glue so the screen can be removed.

The phone will be extremely hot. Avoid direct contact with metal pieces.

Step 11

  • Gently slide the metal spudger underneath the screen and pry it away from the backing.
  • Move the metal spudger under the digitizer and along the entire length of the phone to separate the screen from the adhesive.
  • If the screen was broken, glass shards may come off of the screen and puncture skin.

Gently slide the metal spudger underneath the screen and pry it away from the backing.

Move the metal spudger under the digitizer and along the entire length of the phone to separate the screen from the adhesive.

If the screen was broken, glass shards may come off of the screen and puncture skin.

Step 12

  • Continue to heat and separate until the screen comes completely apart from the rest of the phone.

Continue to heat and separate until the screen comes completely apart from the rest of the phone.

Step 13

  • To put the new screen on, press the new screen and digitizer into place, and then reapply heat to adhere the new screen.

To put the new screen on, press the new screen and digitizer into place, and then reapply heat to adhere the new screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      23 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Alex Craig                     

Member since: 03/11/2015

2,578 Reputation

                                      5 Guides authored                  



                       Badges:
                       23







                                                        +20 more badges                           

Team

                       Colorado Springs, Team 5-7, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 5-7, Panko Spring 2015 



                    UCCS-PANKO-S15S5G7                     


                                            2 Members                     


                                            10 Guides authored