Motorola Moto E 2Nd Generation Battery Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          20 - 35 minutes

Sections

Display Assembly
3 steps
Earpiece Speaker
2 steps
Motherboard
4 steps
Battery
1 step

Flags

BackMotorola Moto E 2nd Generation
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

If your battery is swollen, take appropriate precautions.

What you need

Step 1

              Display Assembly

Turn off the device before beginning your repair.
Using a heat gun, carefully apply heat around the edges of the display to soften the glue. Heat should be applied to the point where the phone isn’t too hot to touch, but close enough.

Turn off the device before beginning your repair.

Using a heat gun, carefully apply heat around the edges of the display to soften the glue. Heat should be applied to the point where the phone isn’t too hot to touch, but close enough.

1024

Step 2

Using the small plastic opening tool, pry and slide all the way around the phone while carefully lifting up on the display.
The screen is secured by two-sided tape located on the edge.

Using the small plastic opening tool, pry and slide all the way around the phone while carefully lifting up on the display.

The screen is secured by two-sided tape located on the edge.

Step 3

Once display is fully unglued from the frame, carefully lift it up and locate the display connector.
Using the same small plastic tool, carefully remove the yellow tape off the connector.
Now carefully undo the black connector lock by lifting it up in the direction of the red arrow.
Do not pry on the gray part of the connector.
Lastly slide the display cable off the connector. It should easily slide off, if not make sure the black lock is fully unlatched.

Once display is fully unglued from the frame, carefully lift it up and locate the display connector.

Using the same small plastic tool, carefully remove the yellow tape off the connector.

Now carefully undo the black connector lock by lifting it up in the direction of the red arrow.

Do not pry on the gray part of the connector.

Lastly slide the display cable off the connector. It should easily slide off, if not make sure the black lock is fully unlatched.

Step 4

              Earpiece Speaker

Now that the display is out, remove the aluminum shield off the motherboard.
Unscrew the single 4mm screw located on the top using a T4 Torx bit.
After screw is out, gently remove the aluminum shield off the motherboard.
Working on a magnet board is recommended as the screws are small and can be easily misplaced.

Now that the display is out, remove the aluminum shield off the motherboard.

Unscrew the single 4mm screw located on the top using a T4 Torx bit.

After screw is out, gently remove the aluminum shield off the motherboard.

Working on a magnet board is recommended as the screws are small and can be easily misplaced.

Step 5

Using the metal spudger tool, very carefully remove the speaker by first gently prying up on the right side and then the bottom.
The ear piece is held by double sided tape and clips to the motherboard so be very careful.

Using the metal spudger tool, very carefully remove the speaker by first gently prying up on the right side and then the bottom.

The ear piece is held by double sided tape and clips to the motherboard so be very careful.

Step 6

              Motherboard

Unscrew the remaining 16- 4mm screws using a T4 Torx bit.
Using a magnet board is recommended as the screws are small and can be easily misplaced.

Unscrew the remaining 16- 4mm screws using a T4 Torx bit.

Using a magnet board is recommended as the screws are small and can be easily misplaced.

Step 7

Next remove the plastic C-shaped black plastic frame.
Using the metal spudger tool, gently pull up the right corner as indicated and work your way around until it’s off the motherboard.

Next remove the plastic C-shaped black plastic frame.

Using the metal spudger tool, gently pull up the right corner as indicated and work your way around until it’s off the motherboard.

Step 8

Gently lift up the battery cable connector, it should come out very easy.

Gently lift up the battery cable connector, it should come out very easy.

Step 9

After the battery cable is disconnected from the motherboard, use the metal spudger tool and carefully insert it in the small opening by the speaker and pry the motherboard up enough to fit your finger in between the motherboard and the phone frame.
Now just pull the motherboard starting from the top to bottom off the phone case.

After the battery cable is disconnected from the motherboard, use the metal spudger tool and carefully insert it in the small opening by the speaker and pry the motherboard up enough to fit your finger in between the motherboard and the phone frame.

Now just pull the motherboard starting from the top to bottom off the phone case.

Step 10

              Battery

Use a spudger to gently pry up the battery.
It’s best to use a non-metal spudger whenever possible, as a metal spudger is much more likely to accidentally puncture/damage the battery.
The battery is stuck to the plastic case with double sided tape.
Obtain a new battery and place it into the plastic casing using double sided tape or whatever is provided with the new battery.

Use a spudger to gently pry up the battery.

It’s best to use a non-metal spudger whenever possible, as a metal spudger is much more likely to accidentally puncture/damage the battery.

The battery is stuck to the plastic case with double sided tape.

Obtain a new battery and place it into the plastic casing using double sided tape or whatever is provided with the new battery.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      39 other people completed this guide.

Author

                                      with 3 other contributors

                    Andre Romualdo

Member since: 02/08/2016

3,741 Reputation

                                      5 Guides authored                  



                       Badges:
                       20







                                                        +17 more badges

Team

                       USF Tampa, Team 12-3, Eyestone Spring 2016                        

                                                  Member of USF Tampa, Team 12-3, Eyestone Spring 2016 



                    USFT-EYESTONE-S16S12G3                     


                                            3 Members                     


                                            14 Guides authored

GRINGOX - Sep 28, 2016

Has anyone tried to Dremel it open from the backside? It’s a cheap phone and I’d almost rather possibly ruin it than spend 30+ minutes tearing it apart.

Wha Dahel - Nov 5, 2016

My phone came with the display falling out and flopping around. Videos only say how to take it apart. How do I fasten the display back on?

Tapas Sarkar - Aug 8, 2017

My bettri chanj

My bettri chanj ani problam

Vishal Ankushkar - Sep 1, 2017

my mobile auto shutdown currunt working

Introduction#

What you need#

Team#

Introduction

What you need

Team