Difficulty
Moderate
Steps
16
Time Required
20 minutes
Sections
3
- Lower Case
- 7 steps
- Battery
- 2 steps
- Motherboard
- 7 steps
Flags
0
BackMotorola Lapdock 100
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- To take off the Keyboard there are three tabs at the top of the Keyboard in the locations shown in the picture that you must press and unclip. They are located behind each of the keys that are removed.
- You do not need to remove any keys to unclip the keyboard. We did this for picture purposes only.
To take off the Keyboard there are three tabs at the top of the Keyboard in the locations shown in the picture that you must press and unclip. They are located behind each of the keys that are removed.
You do not need to remove any keys to unclip the keyboard. We did this for picture purposes only.
1024
Step 2
- You can use a small metal spudger to depress each tab to avoid scratching the keyboard.
You can use a small metal spudger to depress each tab to avoid scratching the keyboard.
Step 3
- Lift up keyboard so that you are able to see the ribbon cable connected to the contact.
Lift up keyboard so that you are able to see the ribbon cable connected to the contact.
Step 4
- Flip up the ZIF connector holding the ribbon cable on the contact as shown in the two pictures and then gently disconnect the ribbon cable.
Flip up the ZIF connector holding the ribbon cable on the contact as shown in the two pictures and then gently disconnect the ribbon cable.
Step 5
- After we remove the Keyboard, you can clearly see the screws under it. Remove the ten 3mm long phillips head screws.
After we remove the Keyboard, you can clearly see the screws under it. Remove the ten 3mm long phillips head screws.
Step 6
- Flip over the Lapdock and remove the four 3.5mm long phillips head screws from the bottom.
Flip over the Lapdock and remove the four 3.5mm long phillips head screws from the bottom.
Step 7
- Use a plastic prying tool to take off the bottom case. Make sure that all of the clips are unclipped before trying to remove the case.
Use a plastic prying tool to take off the bottom case. Make sure that all of the clips are unclipped before trying to remove the case.
Step 8
Battery
- Unplug battery from motherboard.
Unplug battery from motherboard.
Step 9
- Remove the battery.
Remove the battery.
Step 10
Motherboard
- Remove the two 2mm long phillips head screws from the left speaker and move it away from the motherboard.
Remove the two 2mm long phillips head screws from the left speaker and move it away from the motherboard.
Step 11
- Unplug the speakers from the motherboard
Unplug the speakers from the motherboard
Step 12
- Remove the two 2mm long phillips head screws that are holding down the motherboard.
Remove the two 2mm long phillips head screws that are holding down the motherboard.
Step 13
- Disconnect the ribbon cable that attaches to the trackpad from the motherboard.
Disconnect the ribbon cable that attaches to the trackpad from the motherboard.
Step 14
- Disconnect the two wires that attach to the screen from the motherboard.
Disconnect the two wires that attach to the screen from the motherboard.
Step 15
- The motherboard and phone adapter cable should both be free from the lapdock.
The motherboard and phone adapter cable should both be free from the lapdock.
Step 16
- Unplug the two phone adapter cable connections to the motherboard.
Unplug the two phone adapter cable connections to the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Anthony Aiumu
Member since: 01/12/2016
764 Reputation
7 Guides authored
Badges:
8
+5 more badges
Team
Eastern Washington University, Team 1-3, Rowley Winter 2016
Member of Eastern Washington University, Team 1-3, Rowley Winter 2016
EWU-ROWLEY-W16S1G3
4 Members
8 Guides authored
