Motorola Edge 5G Uw 2022 Depth Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

Back Cover
15 steps
Motherboard Cover Removal
3 steps
Battery Disconnect
1 step
Depth Camera
2 steps

Flags

Provided Hardware

A manufacturer provided iFixit with this device or component.

BackMotorola Edge 5G UW (2022)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

For your safety, discharge the battery below 25% before disassembling your phone. This reduces the risk of fire if the battery is accidentally damaged during the repair. If your battery is swollen, take appropriate precautions.

You’ll need replacement adhesive in order to complete this repair.

What you need

Step 1

              Heat the left edge

Completely power off your phone before you begin.
Heat an iOpener and apply it to the back cover’s left edge for two minutes.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the back cover and internal battery are both susceptible to heat damage.

Completely power off your phone before you begin.

Heat an iOpener and apply it to the back cover’s left edge for two minutes.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the back cover and internal battery are both susceptible to heat damage.

1024

Step 2

              Separate the left adhesive

Apply a suction cup to the back of the phone, as close to the bottom left corner as possible.
Pull up on the suction cup with a strong, steady force to create a gap between the back cover and the midframe on the left edge.
Depending on the age of your phone, this may be difficult. If you’re having trouble, apply more heat to the edge and try again.
Insert an opening pick into the gap.

Apply a suction cup to the back of the phone, as close to the bottom left corner as possible.

Pull up on the suction cup with a strong, steady force to create a gap between the back cover and the midframe on the left edge.

Depending on the age of your phone, this may be difficult. If you’re having trouble, apply more heat to the edge and try again.

Insert an opening pick into the gap.

Step 3

              Slice the left adhesive

Slide the pick along the left edge of the phone to slice the adhesive securing the back cover to the frame.
Leave the pick inserted in the top left corner to prevent the adhesive from resealing.

Slide the pick along the left edge of the phone to slice the adhesive securing the back cover to the frame.

Leave the pick inserted in the top left corner to prevent the adhesive from resealing.

Step 4

              Heat the top edge

Apply a heated iOpener to the back cover’s top edge for two minutes.

Apply a heated iOpener to the back cover’s top edge for two minutes.

Step 5

Rotate the pick around the top left corner to slice the adhesive.

Rotate the pick around the top left corner to slice the adhesive.

Step 6

Slide the pick along the top edge to slice the adhesive.
Leave the opening pick inserted in the top right corner to prevent the adhesive from resealing.

Slide the pick along the top edge to slice the adhesive.

Leave the opening pick inserted in the top right corner to prevent the adhesive from resealing.

Step 7

Apply a heated iOpener to the back cover’s right edge for two minutes.

Apply a heated iOpener to the back cover’s right edge for two minutes.

Step 8

Rotate the pick around the top right corner to slice the adhesive.

Rotate the pick around the top right corner to slice the adhesive.

Step 9

Slide the pick along the right edge to slice the adhesive.
Leave the pick inserted in the bottom right corner to prevent the adhesive from resealing.

Slide the pick along the right edge to slice the adhesive.

Leave the pick inserted in the bottom right corner to prevent the adhesive from resealing.

Step 10

Apply a heated iOpener to the back cover’s bottom edge for two minutes.

Apply a heated iOpener to the back cover’s bottom edge for two minutes.

Step 11

Rotate the pick around the bottom right corner to slice the adhesive.

Rotate the pick around the bottom right corner to slice the adhesive.

Step 12

Slide the pick along the bottom edge to slice the adhesive.

Slide the pick along the bottom edge to slice the adhesive.

Step 13

              Heat the camera adhesive

There’s a significant amount of adhesive to the right of the cameras that secures the back cover to the motherboard cover.
Apply a heated iOpener to the right of the cameras for two minutes.

There’s a significant amount of adhesive to the right of the cameras that secures the back cover to the motherboard cover.

Apply a heated iOpener to the right of the cameras for two minutes.

Step 14

              Slice the adhesive around the camera

Insert an opening pick between the back cover and motherboard cover on the top right edge.
Gently pull up on the back cover while sliding the opening pick back and forth along the right side of the cameras to slice the adhesive.
The back cover should detach from the phone at this point.

Insert an opening pick between the back cover and motherboard cover on the top right edge.

Gently pull up on the back cover while sliding the opening pick back and forth along the right side of the cameras to slice the adhesive.

The back cover should detach from the phone at this point.

Step 15

              Remove the back cover

Lift the back cover from the phone and remove it.
If the back cover is still stuck to the midframe, slide an opening pick around the edges of the phone until the cover separates completely.
During reassembly:
This is a good point to test your phone’s functionality before sealing it up. Use this guide to run a hardware test. Be sure to power your phone back down completely before you continue working.
Follow this guide to replace the back cover adhesive.

Lift the back cover from the phone and remove it.

If the back cover is still stuck to the midframe, slide an opening pick around the edges of the phone until the cover separates completely.

During reassembly:

This is a good point to test your phone’s functionality before sealing it up. Use this guide to run a hardware test. Be sure to power your phone back down completely before you continue working.

Follow this guide to replace the back cover adhesive.

Step 16

              Unfasten the motherboard cover

Use a Phillips screwdriver to remove the 13 4 mm screws securing the motherboard cover.

Use a Phillips screwdriver to remove the 13 4 mm screws securing the motherboard cover.

Step 17

              Release the motherboard cover clips

Insert a spudger between the motherboard cover and midframe on the top right edge of the phone.
Pry up with the spudger to release the clips securing the motherboard cover.
During reassembly, press down around the perimeter of the motherboard cover to engage the clips.

Insert a spudger between the motherboard cover and midframe on the top right edge of the phone.

Pry up with the spudger to release the clips securing the motherboard cover.

During reassembly, press down around the perimeter of the motherboard cover to engage the clips.

Step 18

              Remove the motherboard cover

Gently pull the motherboard cover up and away from the phone and remove it.
Don’t pull quickly or forcefully, as the heat spreader very loosely secures the motherboard cover to the battery.

Gently pull the motherboard cover up and away from the phone and remove it.

Don’t pull quickly or forcefully, as the heat spreader very loosely secures the motherboard cover to the battery.

Step 19

              Disconnect the battery

Use the pointed end of a spudger to pry up and disconnect the battery’s press connector.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don’t press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Use the pointed end of a spudger to pry up and disconnect the battery’s press connector.

To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don’t press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Step 20

              Disconnect the depth camera

Use the pointed end of a spudger to pry up and disconnect the depth camera’s press connector.

Use the pointed end of a spudger to pry up and disconnect the depth camera’s press connector.

Step 21

              Remove the depth camera

A small amount of adhesive secures the depth camera.
Use the flat end of a spudger to pry the depth camera out of its housing.
Use your fingers or tweezers to remove the camera.

A small amount of adhesive secures the depth camera.

Use the flat end of a spudger to pry the depth camera out of its housing.

Use your fingers or tweezers to remove the camera.

Compare your new replacement part to the original part—be sure to transfer remaining components and remove adhesive backings from the new part before installing.

To reassemble your device, follow the instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Spencer Day

Member since: 09/14/2022

11,019 Reputation

                                      84 Guides authored                  



                       Badges:
                       21







                                                        +18 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Provided Hardware#

Introduction#

What you need#

Team#

Provided Hardware

Introduction

What you need

Team