Difficulty
Moderate
Steps
14
Time Required
10 minutes
Sections
4
- Battery
- 3 steps
- Disassembling Motorola E815 Antenna
- 2 steps
- Front Screen
- 8 steps
- Inside Screen
- 1 step
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackMotorola E815
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
- Dissemble the phone to access the screen
What you need
Step 1
Battery
- Locate the back cover release slide.
- Use your finger to slide it down.
Locate the back cover release slide.
Use your finger to slide it down.
1024
Step 2
- Remove the back cover by pulling it away from the phone.
Remove the back cover by pulling it away from the phone.
Step 3
- Locate the battery removal slot.
- Use your finger to pull the battery out from the top.
- Remove the battery.
Locate the battery removal slot.
Use your finger to pull the battery out from the top.
Remove the battery.
Step 4
Disassembling Motorola E815 Antenna
- Locate the antenna port on the top of the phone.
Locate the antenna port on the top of the phone.
Step 5
- Grip the plastic support post and unscrew the apparatus using a counterclockwise twist.
- Pull the apparatus up and out of the phone.
Grip the plastic support post and unscrew the apparatus using a counterclockwise twist.
Pull the apparatus up and out of the phone.
Step 6
Front Screen
- Locate the two screws on the backside of the phone.
- Unscrew the two screws using your T6 screwdriver.
Locate the two screws on the backside of the phone.
Unscrew the two screws using your T6 screwdriver.
Step 7
- Grasp the top of the phone near the speaker.
- Gently pull the top section of the phone upwards until you feel some resistance.
- Locate the brown connector that runs from the top section of the phone to the circuit board under the keypad.
- Using tweezers, gently pry the connector from the circuit board.
- Detach the top section of the phone from the keypad section.
Grasp the top of the phone near the speaker.
Gently pull the top section of the phone upwards until you feel some resistance.
Locate the brown connector that runs from the top section of the phone to the circuit board under the keypad.
Using tweezers, gently pry the connector from the circuit board.
Detach the top section of the phone from the keypad section.
Step 8
- Carefully insert the blue pry tool into the notch between the two halves of the top section of the phone.
- Gently pry the two halves apart.
Carefully insert the blue pry tool into the notch between the two halves of the top section of the phone.
Gently pry the two halves apart.
Step 9
- Rotate the top section of the phone around so that you are looking at the outer screen.
- Disconnect the cover from the outer screen side of the phone.
Rotate the top section of the phone around so that you are looking at the outer screen.
Disconnect the cover from the outer screen side of the phone.
Step 10
- Rotate the top section of the phone around so you are looking at the large screen.
- Using your fingers, lift the protector off of the screen.
Rotate the top section of the phone around so you are looking at the large screen.
Using your fingers, lift the protector off of the screen.
Step 11
- Using the blue pry tool, gently remove the screen cover.
- Since it is glued into place, it may take some maneuvering to remove.
Using the blue pry tool, gently remove the screen cover.
Since it is glued into place, it may take some maneuvering to remove.
Step 12
- Turn the phone so that you can see the side metal clasps.
- Using the blue lifter tool, snap the metal clasps off of screen body.
- Proceed to snap all four corners of the metal cover off of the screen body.
Turn the phone so that you can see the side metal clasps.
Using the blue lifter tool, snap the metal clasps off of screen body.
Proceed to snap all four corners of the metal cover off of the screen body.
Step 13
- Using tweezers, gently detach the brown connecting strip from the back of the screen.
- Separate the screen from the phone frame.
- The front screen can now be accessed and replaced!
Using tweezers, gently detach the brown connecting strip from the back of the screen.
Separate the screen from the phone frame.
The front screen can now be accessed and replaced!
Step 14
Inside Screen
- The inside screen can now be accessed for repair or replacement!
The inside screen can now be accessed for repair or replacement!
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 5 other contributors
Zoie E
Member since: 01/12/2011
603 Reputation
5 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team 14-8, Forte Winter 2011
Member of Cal Poly, Team 14-8, Forte Winter 2011
CPSU-FORTE-W11S14G8
5 Members
5 Guides authored