Difficulty
Easy
Steps
15
Time Required
Suggest a time??
Sections
3
- Battery
- 2 steps
- Motherboard
- 12 steps
- Rear Facing Camera
- 1 step
Flags
0
BackMotorola Droid X2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Slide the plastic case off of the back of the phone, exposing the battery.
Slide the plastic case off of the back of the phone, exposing the battery.
1024
Step 2
- Pull up on the red battery release tab and pull the battery out of the phone.
Pull up on the red battery release tab and pull the battery out of the phone.
Step 3
Motherboard
- Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length.
- Be careful to not strip any screws.
Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length.
Be careful to not strip any screws.
Step 4
- Using a prying tool, snap off the front casing on the top and bottom of the phone.
- Be careful not to lose the small rubber piece that sits over the microphone.
Using a prying tool, snap off the front casing on the top and bottom of the phone.
Be careful not to lose the small rubber piece that sits over the microphone.
Step 5
- Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.
Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.
Step 6
- Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.
Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.
Step 7
- Using tweezers, remove the white wire at the top of the phone near the camera.
Using tweezers, remove the white wire at the top of the phone near the camera.
Step 8
- Remove these nine screws using a T-3 torques. These screws should be 2.40 mm in length
Remove these nine screws using a T-3 torques. These screws should be 2.40 mm in length
Step 9
- Using tweezers, removed the white electrical tape on the motherboard.
Using tweezers, removed the white electrical tape on the motherboard.
Step 10
- Using the plastic opening tool, lift up to remove the connector.
Using the plastic opening tool, lift up to remove the connector.
Step 11
- Using a pry tool, lift the jawbone connector.
Using a pry tool, lift the jawbone connector.
Step 12
- Using tweezers, carefully disconnect the cable connector by pulling the cable out.
Using tweezers, carefully disconnect the cable connector by pulling the cable out.
Step 13
- Use a spudger to disconnect the cable connector.
Use a spudger to disconnect the cable connector.
Step 14
- Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.
Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.
Step 15
Rear Facing Camera
- There should be jawbone connector here. However it was broken on this particular device. Lift it up using a pry tool.
- Using tweezers, remove cable from motherboard.
There should be jawbone connector here. However it was broken on this particular device. Lift it up using a pry tool.
Using tweezers, remove cable from motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Aaron Mak
Member since: 10/29/2014
658 Reputation
4 Guides authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team 4-3, Miles Fall 2014
Member of UMass Dartmouth, Team 4-3, Miles Fall 2014
UMASSD-MILES-F14S4G3
3 Members
8 Guides authored
Brianna Dittbrenner - Apr 3, 2017
Reply
how do u get it back on when it dose not come back on
brianna
