Motorola Droid X Camera Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes

Sections

Battery
5 steps
Motorola Droid X Rear Housing
9 steps
Motherboard
9 steps
Camera
4 steps

Flags

BackMotorola Droid X
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Locate the power button at the top of the phone. Depress power button for 2 seconds until a menu appears.

Locate the power button at the top of the phone. Depress power button for 2 seconds until a menu appears.

1024

Step 2

Once the menu appears, select the “power off” option. Wait until the phone is completely off.

Once the menu appears, select the “power off” option. Wait until the phone is completely off.

Step 3

Place thumb on the back cover, and push down towards the bottom of the device. Once the cover releases, pull it away from the phone and set it aside.

Place thumb on the back cover, and push down towards the bottom of the device. Once the cover releases, pull it away from the phone and set it aside.

Step 4

Find the yellow pull tab located in the upper left corner. Pull the tab until the battery dislodges. Grab the battery by the raised edge, and remove it from the case.

Find the yellow pull tab located in the upper left corner. Pull the tab until the battery dislodges. Grab the battery by the raised edge, and remove it from the case.

Step 5

The battery has been successfully removed.

The battery has been successfully removed.

Step 6

              Motorola Droid X Rear Housing

Remove the micro SD card from its connector.

Remove the micro SD card from its connector.

Step 7

Locate the seam between the back case and the end cover on the top edge of the phone.
Use the plastic opening tool to detach the two clips by wedging the tool into the right side of the seam and moving right to left. Once the cover comes off set it aside

Locate the seam between the back case and the end cover on the top edge of the phone.

Use the plastic opening tool to detach the two clips by wedging the tool into the right side of the seam and moving right to left. Once the cover comes off set it aside

Step 8

Repeat step 2 on the bottom cover.

Repeat step 2 on the bottom cover.

Step 9

Use a T5 Torx screwdriver to remove the screws in each corner of the phone.
The screws are very small so make sure not to lose them.

Use a T5 Torx screwdriver to remove the screws in each corner of the phone.

The screws are very small so make sure not to lose them.

Step 10

Flip the phone over and locate the screw on the middle of the left side. Unscrew it using the T5 Torx screwdriver and set it aside.

Flip the phone over and locate the screw on the middle of the left side. Unscrew it using the T5 Torx screwdriver and set it aside.

Step 11

Identify the screw located in the bottom right corner of the battery case. Remove the screw with a T5 (or in some cases T6) torx screwdriver and set it aside.

Identify the screw located in the bottom right corner of the battery case. Remove the screw with a T5 (or in some cases T6) torx screwdriver and set it aside.

Step 12

Locate the seam along the right edge of the phone. Use the prying tool to disconnect the two clips along the edge.

Locate the seam along the right edge of the phone. Use the prying tool to disconnect the two clips along the edge.

Step 13

Locate the two clips on the inside of the case and use the spudger tool to detach them from the case. To detach each clip, use the sharp end to press the small, black plastic in the center of the clip.

Locate the two clips on the inside of the case and use the spudger tool to detach them from the case. To detach each clip, use the sharp end to press the small, black plastic in the center of the clip.

Step 14

After the clips are detached, remove the back case and set it aside.

After the clips are detached, remove the back case and set it aside.

Step 15

              Motherboard

Remove the screws along both sides of the motherboard using a T3 Torx screwdriver. On some phones this may require a #1 Phillips Screw Driver.

Remove the screws along both sides of the motherboard using a T3 Torx screwdriver. On some phones this may require a #1 Phillips Screw Driver.

Step 16

Carefully remove the white connecting wire from the motherboard using tweezers.
Use caution, this wire is delicate.

Carefully remove the white connecting wire from the motherboard using tweezers.

Use caution, this wire is delicate.

Step 17

Scrape away the electrical tape that covers the LCD and digitizer cable using the spudger tool or a fingernail.

Scrape away the electrical tape that covers the LCD and digitizer cable using the spudger tool or a fingernail.

Step 18

Use the spudger tool to pop the Digitizer cable off of the motherboard.

Use the spudger tool to pop the Digitizer cable off of the motherboard.

Step 19

Carefully flip the small white connector up and away from the motherboard.

Carefully flip the small white connector up and away from the motherboard.

Step 20

Gently pull the flat gold cable out from the connector.

Gently pull the flat gold cable out from the connector.

Step 21

Carefully lift the motherboard and camera module up. Do not remove it from the phone!

Carefully lift the motherboard and camera module up. Do not remove it from the phone!

Step 22

Using the spudger tool, pop the black cable connector off of the motherboard.

Using the spudger tool, pop the black cable connector off of the motherboard.

Step 23

It is to safe remove the motherboard from the phone.

It is to safe remove the motherboard from the phone.

Step 24

              Camera

Gently peel the camera’s orange and gold connection cable from the motherboard.

Gently peel the camera’s orange and gold connection cable from the motherboard.

Step 25

Remove the black electrical tape covering the cameras connection cable.

Remove the black electrical tape covering the cameras connection cable.

Step 26

Flip up the small white connector. Then gently pull the orange cable out of the connecter.

Flip up the small white connector. Then gently pull the orange cable out of the connecter.

Step 27

Reconnect the camera module by pushing the black end of the flat cable on the camera module into the white connector on the motherboard.

Reconnect the camera module by pushing the black end of the flat cable on the camera module into the white connector on the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors

                    Sam Johnston

Member since: 10/03/2012

555 Reputation

                                      4 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 18-40, Regan Fall 2012                        

                                                  Member of Cal Poly, Team 18-40, Regan Fall 2012 



                    CPSU-REGAN-F12S18G40                     


                                            3 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team