Motorola Droid Rear Case Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 minutes

Sections

Battery
2 steps
Rear Case
9 steps

Flags

BackMotorola Droid 1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Slide the battery cover downwards while applying pressure to the center of the battery cover with your thumb.
Lift and remove the battery cover out from the phone.

Slide the battery cover downwards while applying pressure to the center of the battery cover with your thumb.

Lift and remove the battery cover out from the phone.

1024

Step 2

Grasp the upper left corner of the battery and lift it out of its housing.

Grasp the upper left corner of the battery and lift it out of its housing.

Step 3

              Rear Case

Use a spudger to lift and remove the black plastic screw cover at the top of the phone near the camera.
The cover is attached by adhesive, so some force may be required.

Use a spudger to lift and remove the black plastic screw cover at the top of the phone near the camera.

The cover is attached by adhesive, so some force may be required.

Step 4

Using the tip of a spudger, peel up one corner of the gold ribbon beneath the battery compartment.
Peel the ribbon up off the phone.

Using the tip of a spudger, peel up one corner of the gold ribbon beneath the battery compartment.

Peel the ribbon up off the phone.

Step 5

Carefully peel the device information label that covers the motherboard EMI shields.
This label contains important information specific to the phone. Remove it with care and keep it in a safe place.

Carefully peel the device information label that covers the motherboard EMI shields.

This label contains important information specific to the phone. Remove it with care and keep it in a safe place.

Step 6

Insert the flat end of a spudger and pry the plastic camera cover up off the phone.
The thin plastic cover is attached to the phone with an adhesive. Work slowly and carefully.

Insert the flat end of a spudger and pry the plastic camera cover up off the phone.

The thin plastic cover is attached to the phone with an adhesive. Work slowly and carefully.

Step 7

Remove the seven 5.5 mm T5 Torx screws securing the rear case to the inner case.

Remove the seven 5.5 mm T5 Torx screws securing the rear case to the inner case.

Step 8

Insert the flat end of a spudger and pry downwards to release the plastic tab holding the rear case to the motherboard screw.

Insert the flat end of a spudger and pry downwards to release the plastic tab holding the rear case to the motherboard screw.

Step 9

Gently insert a spudger between the rear case and front case at the top of the phone, near the audio jack.
Carefully pry the top edge of the rear case up from the rest of the phone.

Gently insert a spudger between the rear case and front case at the top of the phone, near the audio jack.

Carefully pry the top edge of the rear case up from the rest of the phone.

Step 10

With the spudger still inserted between the rear case and front case, slide the spudger along the right edge of the device, moving toward the bottom, prying as you go.
Continue prying along the bottom edge of the device from right to left, freeing it from the front panel.

With the spudger still inserted between the rear case and front case, slide the spudger along the right edge of the device, moving toward the bottom, prying as you go.

Continue prying along the bottom edge of the device from right to left, freeing it from the front panel.

Step 11

Continue prying the rear case from the front case along the left side, moving from bottom to top.
Lift the rear case up out of the phone.

Continue prying the rear case from the front case along the left side, moving from bottom to top.

Lift the rear case up out of the phone.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 6 other contributors

                    Brett Hartt

Member since: 04/12/2010

125,280 Reputation

                                      143 Guides authored                  



                       Badges:
                       52







                                                        +49 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team