Difficulty
Moderate
Steps
8
Time Required
5 - 10 minutes
Sections
1
- Front Assembly
- 8 steps
Flags
0
BackMotorola Droid RAZR M
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Assembly
- Open the small latch on the left side of the device by lifting gently with your finger, exposing the SIM card and microSD card slots.
- If either of these cards are present, remove them to prevent damaging them while taking apart the phone. Our device does not have either.
- Close the latch once the two cards are removed.
Open the small latch on the left side of the device by lifting gently with your finger, exposing the SIM card and microSD card slots.
If either of these cards are present, remove them to prevent damaging them while taking apart the phone. Our device does not have either.
Close the latch once the two cards are removed.
1024
Step 2
- Remove the six 4mm T3 Torx screws. There are 3 on each side of the device.
Remove the six 4mm T3 Torx screws. There are 3 on each side of the device.
Step 3
- Run the plastic opening tool under the bottom edge of the phone to detach the small plastic cover below the Verizon logo.
- It will take some force to remove this piece. Work around the bottom corners to unlatch the two hooks holding the piece in place.
- The small plastic hooks can break during removal. Be careful that you don’t damage them, but it will take some force to get them undone.
- Once the plastic cover is detached, pull the piece away with your fingers.
Run the plastic opening tool under the bottom edge of the phone to detach the small plastic cover below the Verizon logo.
It will take some force to remove this piece. Work around the bottom corners to unlatch the two hooks holding the piece in place.
The small plastic hooks can break during removal. Be careful that you don’t damage them, but it will take some force to get them undone.
Once the plastic cover is detached, pull the piece away with your fingers.
Step 4
- Remove the three T4 Torx screws. There are three at the bottom of the device.
Remove the three T4 Torx screws. There are three at the bottom of the device.
Step 5
- Using the plastic opening tool, peel away the silver Motorola plate at the top of the phone. There is a fair amount of adhesive underneath, so you may have to pry it from a few different angles.
- As soon as you can get your finger underneath, pull away the silver plate.
Using the plastic opening tool, peel away the silver Motorola plate at the top of the phone. There is a fair amount of adhesive underneath, so you may have to pry it from a few different angles.
As soon as you can get your finger underneath, pull away the silver plate.
Step 6
- Remove the two 7mm T4 Torx screws at the top of the device.
Remove the two 7mm T4 Torx screws at the top of the device.
Step 7
- When you detach the front from the back, don’t pull the two pieces entirely apart. There is a flat orange wire that connects the two pieces that will be disconnected in the next step.
- Snap apart the two internal clips located on the top corners of the device, and the two clips in the bottom corners.
- Run the plastic opening tool around the edge of the entire device to pry apart the front of the phone from the back.
- There is a small black plastic piece located at the bottom of the front assembly. Do not worry if the strip falls off; just simply snap it back on and proceed.
When you detach the front from the back, don’t pull the two pieces entirely apart. There is a flat orange wire that connects the two pieces that will be disconnected in the next step.
Snap apart the two internal clips located on the top corners of the device, and the two clips in the bottom corners.
Run the plastic opening tool around the edge of the entire device to pry apart the front of the phone from the back.
There is a small black plastic piece located at the bottom of the front assembly. Do not worry if the strip falls off; just simply snap it back on and proceed.
Step 8
- Like a clamshell, slowly open the device from the top. Open the remainder of the device slowly while being mindful of the flat orange wire that connects the motherboard to the front assembly.
- Undo the snap connection in the lower left corner by inserting the plastic opening tool under the end of the orange wire connected to the motherboard. Lift gently.
- Once the snap connection is undone, pull apart the front assembly from the rest of the phone.
Like a clamshell, slowly open the device from the top. Open the remainder of the device slowly while being mindful of the flat orange wire that connects the motherboard to the front assembly.
Undo the snap connection in the lower left corner by inserting the plastic opening tool under the end of the orange wire connected to the motherboard. Lift gently.
Once the snap connection is undone, pull apart the front assembly from the rest of the phone.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 2 other contributors
Ethan Look
Member since: 04/21/2015
498 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 15-1, Amido Spring 2015
Member of Cal Poly, Team 15-1, Amido Spring 2015
CPSU-AMIDO-S15S15G1
4 Members
14 Guides authored