Difficulty
Moderate
Steps
7
Time Required
10 - 15 minutes
Sections
2
- Front Panel Assembly
- 5 steps
- Rear Facing Camera
- 2 steps
Flags
0
BackMotorola Droid RAZR HD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Panel Assembly
- Power off the device before disassembly to avoid damage or harm from electrical surges.
- Remove the two 4.5mm screws in the bottom left and right corners of the device using a T4 Torx Screwdriver.
Power off the device before disassembly to avoid damage or harm from electrical surges.
Remove the two 4.5mm screws in the bottom left and right corners of the device using a T4 Torx Screwdriver.
1024
Step 2
- Holding the device in your hand, push the screen towards the top of the phone until it disconnects from the base of the phone.
Holding the device in your hand, push the screen towards the top of the phone until it disconnects from the base of the phone.
Step 3
- Use a plastic opening tool to lift the screen from the phone.
- Do not try to completely detach the screen; cables are still connected to the device and can be damaged.
Use a plastic opening tool to lift the screen from the phone.
Do not try to completely detach the screen; cables are still connected to the device and can be damaged.
Step 4
- Use tweezers to remove the yellow tape covering the lcd/digitizer cable connector.
- Carefully lift up the black locking tab to release the lcd/digitizer cable.
- The cable connector is located on the bottom right section of the phone.
Use tweezers to remove the yellow tape covering the lcd/digitizer cable connector.
Carefully lift up the black locking tab to release the lcd/digitizer cable.
The cable connector is located on the bottom right section of the phone.
Step 5
- Lift up the screen further to reveal another cable at the top of the device connecting the motherboard to the screen.
- This connector is located on the top right section of the phone.
- Use tweezers to lift the black bar on top of the ZIF connector.
- Pull the ribbon cable out of the connector with tweezers.
- Now that there are no cables connecting the screen to the motherboard, remove the screen.
Lift up the screen further to reveal another cable at the top of the device connecting the motherboard to the screen.
This connector is located on the top right section of the phone.
Use tweezers to lift the black bar on top of the ZIF connector.
Pull the ribbon cable out of the connector with tweezers.
Now that there are no cables connecting the screen to the motherboard, remove the screen.
Step 6
Rear Facing Camera
- Remove the two 3.5mm Torx T4 screws securing the rear facing camera.
- Using tweezers, remove the metal shield protecting the rear facing camera.
Remove the two 3.5mm Torx T4 screws securing the rear facing camera.
Using tweezers, remove the metal shield protecting the rear facing camera.
Step 7
- Use a plastic opening tool to lift up the rear camera.
- Use tweezers to lift and unlock the black bar on top of the rear camera’s ZIF connector.
- Pull the camera out of the connector.
- You will need to unplug the rear camera from its connector on the motherboard.
Use a plastic opening tool to lift up the rear camera.
Use tweezers to lift and unlock the black bar on top of the rear camera’s ZIF connector.
Pull the camera out of the connector.
You will need to unplug the rear camera from its connector on the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Ryan Meinhardt
Member since: 04/14/2015
346 Reputation
1 Guide authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 4-4, Maness Spring 2015
Member of Cal Poly, Team 4-4, Maness Spring 2015
CPSU-MANESS-S15S4G4
5 Members
12 Guides authored
