Difficulty
Moderate
Steps
10
Time Required
15 - 30 minutes
Sections
5
- Rear Panel
- 1 step
- Battery
- 2 steps
- Rear Bezel
- 3 steps
- Motherboard Housing
- 2 steps
- Motherboard
- 2 steps
Flags
3
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackMotorola Droid 4
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
You will need to remove several torx head screws. Make sure to use the correct type.
What you need
Step 1
Removing Rear Panel
- Insert the rear cover removal tool, or a paper clip, in the hole near the back camera lens.
- Slide the cover down to remove.
Insert the rear cover removal tool, or a paper clip, in the hole near the back camera lens.
Slide the cover down to remove.
1024
Step 2
Battery
- Remove the sticker on the rear compartment to reveal the battery.
- Hold the battery with your thumb while removing the sticker or you might end up ripping the battery out of the phone, damaging the flex cable.
Remove the sticker on the rear compartment to reveal the battery.
Hold the battery with your thumb while removing the sticker or you might end up ripping the battery out of the phone, damaging the flex cable.
Step 3
- Use the T5 Torx Screwdriver to remove both 2.5 mm screws from the battery cable.
- Use the Spudger to unstick the battery.
- It’s difficult to remove the battery without a pry tool like the spudger because of the strong adhesive. If you try removing it with just your fingers, the battery may bend.
Use the T5 Torx Screwdriver to remove both 2.5 mm screws from the battery cable.
Use the Spudger to unstick the battery.
It’s difficult to remove the battery without a pry tool like the spudger because of the strong adhesive. If you try removing it with just your fingers, the battery may bend.
Step 4
Camera Cover Removal
- Using the blue plastic opening tool, pry off the thin plastic camera cover.
- The plastic cover is fragile, so proceed carefully.
Using the blue plastic opening tool, pry off the thin plastic camera cover.
The plastic cover is fragile, so proceed carefully.
Step 5
Remove Screws
- Remove the four screws, indicated by the red circles, with the screwdriver and T5 Torx bit.
- The screws are philips 2.5mm. One screw is a different color (silver) from the others (black).
Remove the four screws, indicated by the red circles, with the screwdriver and T5 Torx bit.
The screws are philips 2.5mm. One screw is a different color (silver) from the others (black).
Step 6
Remove Bezel
- Insert the spudger between the rear bezel and the main housing.
- The bezel is fragile, so proceed carefully.
- Slide the spudger around all sides of the phone to separate the bezel from the housing.
- Pry the bezel free.
- Be careful of the adhesive that holds the bezel to the main housing. Prying too hard may damage your phone.
Insert the spudger between the rear bezel and the main housing.
The bezel is fragile, so proceed carefully.
Slide the spudger around all sides of the phone to separate the bezel from the housing.
Pry the bezel free.
Be careful of the adhesive that holds the bezel to the main housing. Prying too hard may damage your phone.
Step 7
Removing screws
- Remove the 12 screws holding the housing in place using a T5 Torx screwdriver.
- Follow the red circles, indicated in the picture, to locate the screws.
- The 12 screws are (silver) philips 2.5mm
Remove the 12 screws holding the housing in place using a T5 Torx screwdriver.
Follow the red circles, indicated in the picture, to locate the screws.
The 12 screws are (silver) philips 2.5mm
Step 8
Separation of the Housing from the Motherboard
- Separate the housing from the motherboard.
- Be careful while separating the housing. The power and volume buttons are easily separated from the housing and can be damaged.
Separate the housing from the motherboard.
Be careful while separating the housing. The power and volume buttons are easily separated from the housing and can be damaged.
Step 9
Motherboard
- The Motherboard is the brain of the phone, handle with care.
- Using the spudger, separate the motherboard from the keyboard frame.
- Tilt the motherboard upward from the side of the charger connection as shown in the picture.
The Motherboard is the brain of the phone, handle with care.
Using the spudger, separate the motherboard from the keyboard frame.
Tilt the motherboard upward from the side of the charger connection as shown in the picture.
Step 10
Disconnecting the Motherboard
- Using the spudger, gently disconnect the two motherboard connections.
- Once the motherboard is separated from the phone place it in a safe place.
Using the spudger, gently disconnect the two motherboard connections.
Once the motherboard is separated from the phone place it in a safe place.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Javier
Member since: 09/29/2014
530 Reputation
4 Guides authored
Badges:
8
+5 more badges
Team
USF Tampa, Team 5-1, Mcgee Fall 2014
Member of USF Tampa, Team 5-1, Mcgee Fall 2014
USFT-MCGEE-F14S5G1
5 Members
5 Guides authored