Difficulty
Moderate
Steps
8
Time Required
15 minutes
Sections
3
- Battery
- 2 steps
- Rear Casing
- 5 steps
- Keypad & Faceplate
- 1 step
Flags
1
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
BackMotorola C139
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Begin by flipping your phone over so that the back cover is facing up.
- Apply force to the back cover and simultaneously slide the cover down.
- Note: Applying pressure on the ridges will make it easier to remove the cover.
Begin by flipping your phone over so that the back cover is facing up.
Apply force to the back cover and simultaneously slide the cover down.
Note: Applying pressure on the ridges will make it easier to remove the cover.
1024
Step 2
- Press the button labeled “PUSH” located at the bottom back of the phone. This will release the battery.
- Lift and remove the battery.
Press the button labeled “PUSH” located at the bottom back of the phone. This will release the battery.
Lift and remove the battery.
Step 3
Rear Casing
- Use a Torx T-5 screwdriver to remove the screws on the back of the phone.
- The screws are 6.86 mm long and 1.61 mm in diameter.
Use a Torx T-5 screwdriver to remove the screws on the back of the phone.
The screws are 6.86 mm long and 1.61 mm in diameter.
Step 4
- Slide a pry tool underneath the adhesive rubber stip and peel it back away from the phone.
- Repeat for the other side.
Slide a pry tool underneath the adhesive rubber stip and peel it back away from the phone.
Repeat for the other side.
Step 5
- Insert the pry tool in the slit on the side of the phone and slide it down until you hear an audible click and the phone bottom loosens from the top.
- Use the pry tool to release the two hooks on each side and the two hooks at the top holding the case together.
- Release a total of six hooks from the sides and top to free the phone into two halves.
Insert the pry tool in the slit on the side of the phone and slide it down until you hear an audible click and the phone bottom loosens from the top.
Use the pry tool to release the two hooks on each side and the two hooks at the top holding the case together.
Release a total of six hooks from the sides and top to free the phone into two halves.
Step 6
- Using a Torx T-5 screwdriver remove the screws at the top of the phone.
- The screws are 6.86 mm long and 1.61mm in diameter.
Using a Torx T-5 screwdriver remove the screws at the top of the phone.
The screws are 6.86 mm long and 1.61mm in diameter.
Step 7
- Use plastic opening tools to free the circuit board from the case.
- There are two hooks (one on each side) holding the circuit board into the case.
- Then grip the circuit board and lift to remove the circuit board from the case.
Use plastic opening tools to free the circuit board from the case.
There are two hooks (one on each side) holding the circuit board into the case.
Then grip the circuit board and lift to remove the circuit board from the case.
Step 8
Keypad & Faceplate
- On the top half of the phone push downwards on the number keys to free the keypad from the top of the phone.
On the top half of the phone push downwards on the number keys to free the keypad from the top of the phone.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Christopher Stubbs
Member since: 03/09/2012
56 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
Clemson, Team 2-2, Benson Spring 2012
Member of Clemson, Team 2-2, Benson Spring 2012
CLEM-BENSON-S12S2G2
3 Members
15 Guides authored
