Motorola Atrix Hd Touchscreen And Lcd Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Battery
7 steps
Rear Chassis
3 steps
Touchscreen and LCD display
6 steps

Flags

Scenic Route

This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.

BackMotorola Atrix HD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Before disassembling the phone, remove the SIM card and the MICRO-SD card, if equipped.
Begin taking apart the device by prying apart the back cover from the assembly using the plastic opening tool.
Continue working around the edge of the phone using the plastic opening tool.
When all the edges have been lifted apart, use your hands or plastic opening tool to peel the back plate from the battery. There are small adhesive strips between the back cover and the battery, so take care not to crack the back cover while prying open.

Before disassembling the phone, remove the SIM card and the MICRO-SD card, if equipped.

Begin taking apart the device by prying apart the back cover from the assembly using the plastic opening tool.

Continue working around the edge of the phone using the plastic opening tool.

When all the edges have been lifted apart, use your hands or plastic opening tool to peel the back plate from the battery. There are small adhesive strips between the back cover and the battery, so take care not to crack the back cover while prying open.

1024

Step 2

The adhesive strips are shown in the orange boxes. Be sure not to use too much force to pull off the back cover, or you may risk snapping the back cover.

The adhesive strips are shown in the orange boxes. Be sure not to use too much force to pull off the back cover, or you may risk snapping the back cover.

Step 3

Remove the red rubber screw cover with a pair of tweezers

Remove the red rubber screw cover with a pair of tweezers

Step 4

Use the T-5 Torx bit to remove the two silver 3.3 mm screws with integrated washers.

Use the T-5 Torx bit to remove the two silver 3.3 mm screws with integrated washers.

Step 5

Lift the battery leads to the upward position. The ribbon cable is very thin, be gentle.

Lift the battery leads to the upward position. The ribbon cable is very thin, be gentle.

Step 6

Use the plastic opening tool around the edges to loosen the battery.
Once the battery is loose, carefully lift from the bottom edge and remove the battery.

Use the plastic opening tool around the edges to loosen the battery.

Once the battery is loose, carefully lift from the bottom edge and remove the battery.

Step 7

The battery may now be removed.

The battery may now be removed.

Step 8

              Rear Chassis

Begin by removing the back cover using the plastic opening tool. There are adhesive strips attached to the back cover, so take care when prying case to prevent cracking
The adhesive strips may stay on the back cover or the battery.

Begin by removing the back cover using the plastic opening tool. There are adhesive strips attached to the back cover, so take care when prying case to prevent cracking

The adhesive strips may stay on the back cover or the battery.

Step 9

The back case portion may be removed after the battery has been removed.
Use the T5 Torx screwdriver to remove the 10 coarse-thread 5mm screws

The back case portion may be removed after the battery has been removed.

Use the T5 Torx screwdriver to remove the 10 coarse-thread 5mm screws

Step 10

Now with the screws removed, use the plastic opening tool to lift the edges of the front assembly.
Continue to use the plastic opening tool around the edges of the device to remove the front assembly.
The speaker is located in the upper corner of the case. It it attached with adhesive and can be removed by gently prying with the plastic opening tool

Now with the screws removed, use the plastic opening tool to lift the edges of the front assembly.

Continue to use the plastic opening tool around the edges of the device to remove the front assembly.

The speaker is located in the upper corner of the case. It it attached with adhesive and can be removed by gently prying with the plastic opening tool

Step 11

              Touchscreen and LCD display

Begin by removing the 10 Torx T5 motherboard baseplate screws
The back chassis can now be removed.

Begin by removing the 10 Torx T5 motherboard baseplate screws

The back chassis can now be removed.

Step 12

Remove the 10 Torx T5 screws, that hold the metal frame to the motherboard.

Remove the 10 Torx T5 screws, that hold the metal frame to the motherboard.

Step 13

After following the steps to access the motherboard, you are ready to remove the touchscreen and LCD display.
Use the plastic opening tool to separate the LCD display from the motherboard.
The touchscreen may separate from the LCD, however they are both connected to the motherboard as one unit.

After following the steps to access the motherboard, you are ready to remove the touchscreen and LCD display.

Use the plastic opening tool to separate the LCD display from the motherboard.

The touchscreen may separate from the LCD, however they are both connected to the motherboard as one unit.

Step 14

Remove the ribbon cable from the back of the lcd using the plastic opening tool or spudger.
Use care removing the ribbon cables. They are very thin and are broken easily.

Remove the ribbon cable from the back of the lcd using the plastic opening tool or spudger.

Use care removing the ribbon cables. They are very thin and are broken easily.

Step 15

Remove the ribbon cable connecting the LCD display to the motherboard, be mindful that the ribbon cable is very thin.
With the LCD display removed, remove the ribbon cable connecting the touchscreen to the motherboard

Remove the ribbon cable connecting the LCD display to the motherboard, be mindful that the ribbon cable is very thin.

With the LCD display removed, remove the ribbon cable connecting the touchscreen to the motherboard

Step 16

The LCD display and the touchscreen may now be replaced.

The LCD display and the touchscreen may now be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 2 other contributors

                    Gabriel Agaman

Member since: 10/28/2015

576 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       UMass Dartmouth, Team 1-8, Miles Fall 2015                        

                                                  Member of UMass Dartmouth, Team 1-8, Miles Fall 2015 



                    UMASSD-MILES-F15S1G8                     


                                            3 Members                     


                                            10 Guides authored

Scenic Route#

Introduction#

What you need#

Team#

Scenic Route

Introduction

What you need

Team