Difficulty
Moderate
Steps
24
Time Required
30 minutes
Sections
5
- Back Cover
- 4 steps
- Midframe
- 7 steps
- Battery Disconnection
- 1 step
- Motherboard
- 9 steps
- Rear-facing Camera
- 3 steps
Flags
3
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Needs More Images
A few more images would make this guide’s procedures crystal clear.
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
BackMoto G4
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Insert a fingernail or a spudger into the notch on the bottom edge of the phone, near the charge port.
- Gently twist or pry to open a small gap between the back cover and the body of the phone.
- While keeping your tool (or fingernail) inserted into the gap between the back cover and the body of the phone, slide it around the corner to begin loosening the plastic clips holding the cover in place.
Insert a fingernail or a spudger into the notch on the bottom edge of the phone, near the charge port.
Gently twist or pry to open a small gap between the back cover and the body of the phone.
While keeping your tool (or fingernail) inserted into the gap between the back cover and the body of the phone, slide it around the corner to begin loosening the plastic clips holding the cover in place.
1024
Step 2
- Slide your tool all along the side of the phone to separate more of the clips securing the back cover.
Slide your tool all along the side of the phone to separate more of the clips securing the back cover.
Step 3
- Keep your tool inserted slightly under the back cover, and slide it around the top corner.
- If necessary, continue prying around the remaining edges of the phone until the back cover comes free.
Keep your tool inserted slightly under the back cover, and slide it around the top corner.
If necessary, continue prying around the remaining edges of the phone until the back cover comes free.
Step 4
- Remove the back cover.
- To install the back cover, carefully position it over the phone and then press gently all around the edges until you feel the clips snap into place.
Remove the back cover.
To install the back cover, carefully position it over the phone and then press gently all around the edges until you feel the clips snap into place.
Step 5
Midframe
- Push to eject and remove the MicroSD and SIM cards (if installed).
Push to eject and remove the MicroSD and SIM cards (if installed).
Step 6
- Use a spudger to pry up the rubber cover for the camera flash connector.
Use a spudger to pry up the rubber cover for the camera flash connector.
Step 7
- Remove the rubber cover.
Remove the rubber cover.
Step 8
- Use a spudger to disconnect the camera flash connector by prying it straight up.
Use a spudger to disconnect the camera flash connector by prying it straight up.
Step 9
- Use a T3 Torx driver to remove the nineteen identical 3.1 mm screws securing the midframe.
Use a T3 Torx driver to remove the nineteen identical 3.1 mm screws securing the midframe.
Step 10
- Insert a spudger under the midframe at the top left corner, and gently twist to separate it from the body of the phone.
Insert a spudger under the midframe at the top left corner, and gently twist to separate it from the body of the phone.
Step 11
- Remove the midframe.
Remove the midframe.
Step 12
Battery Disconnection
- Insert a thin tool (such as one of your tweezer tips) under the red and black battery wires, and slide it underneath the battery connector.
- Gently pry straight up to disconnect the battery.
- Pry only from the side where the wires attach to the connector—if you pry anywhere else, you may break the socket.
- During reassembly, align the connector in its socket and then press straight down to reconnect it, wiggling slightly as you press to help it seat correctly.
Insert a thin tool (such as one of your tweezer tips) under the red and black battery wires, and slide it underneath the battery connector.
Gently pry straight up to disconnect the battery.
Pry only from the side where the wires attach to the connector—if you pry anywhere else, you may break the socket.
During reassembly, align the connector in its socket and then press straight down to reconnect it, wiggling slightly as you press to help it seat correctly.
Step 13
Motherboard
- Peel off any tape securing the battery wires, and then push the battery wires towards the battery to de-route them from the black bracket on the motherboard.
Peel off any tape securing the battery wires, and then push the battery wires towards the battery to de-route them from the black bracket on the motherboard.
Step 14
- It’s not necessary to remove the battery in order to remove or replace the motherboard. You can safely ignore the fact that the battery is missing in the remaining images in this guide.
- Peel up and remove the black rubber cover from the charging port and vibration motor connector.
It’s not necessary to remove the battery in order to remove or replace the motherboard. You can safely ignore the fact that the battery is missing in the remaining images in this guide.
Peel up and remove the black rubber cover from the charging port and vibration motor connector.
Step 15
- Insert the point of your spudger underneath the vibration motor, and gently pry up to separate it from the frame.
Insert the point of your spudger underneath the vibration motor, and gently pry up to separate it from the frame.
Step 16
- Peel up the copper tape covering the display connector.
- This tape provides protection from electromagnetic interference. Keep it in one piece if possible, and carefully fold it back into position when your repair is complete.
Peel up the copper tape covering the display connector.
This tape provides protection from electromagnetic interference. Keep it in one piece if possible, and carefully fold it back into position when your repair is complete.
Step 17
- Use your spudger to disconnect the display by prying its connector straight up from the motherboard, on the edge nearest the side of the phone.
Use your spudger to disconnect the display by prying its connector straight up from the motherboard, on the edge nearest the side of the phone.
Step 18
- Pry up with your spudger to flip open the locking flap on the headphone jack’s ZIF connector.
- It’s possible to disconnect the headphone jack at this point by pulling its orange flex cable straight out of the ZIF socket, but it’s easy to tear the cable if you’re not careful. For a better method, continue with the steps below.
Pry up with your spudger to flip open the locking flap on the headphone jack’s ZIF connector.
It’s possible to disconnect the headphone jack at this point by pulling its orange flex cable straight out of the ZIF socket, but it’s easy to tear the cable if you’re not careful. For a better method, continue with the steps below.
Step 19
- Use a T3 Torx driver to remove the two bronze-colored, 2.4 mm screws securing the motherboard.
Use a T3 Torx driver to remove the two bronze-colored, 2.4 mm screws securing the motherboard.
Step 20
- Grasping the motherboard by its edges, left the bottom end up at an angle, while keeping the top edge close to the phone.
- Use your spudger to pry up the front-facing camera and make sure it separates safely from the frame. The camera can remain attached to the motherboard.
- Using your tweezers, grasp the headphone jack flex cable and carefully pull it out of its socket as you remove the motherboard.
- Remove the motherboard.
- If you feel any resistance, stop. Make sure there are no components still holding the frame to the motherboard.
Grasping the motherboard by its edges, left the bottom end up at an angle, while keeping the top edge close to the phone.
Use your spudger to pry up the front-facing camera and make sure it separates safely from the frame. The camera can remain attached to the motherboard.
Using your tweezers, grasp the headphone jack flex cable and carefully pull it out of its socket as you remove the motherboard.
Remove the motherboard.
If you feel any resistance, stop. Make sure there are no components still holding the frame to the motherboard.
Step 21
- If desired, remove the remaining components from the motherboard (cameras and vibration motor).
If desired, remove the remaining components from the motherboard (cameras and vibration motor).
Step 22
Rear-facing Camera
- Flip motherboard over to access the rear camera.
- Peel up orange tape and remove to access the top of rear camera motherboard clamp.
- Flip up the black tab on the ZIF connector to detach the rear camera.
Flip motherboard over to access the rear camera.
Peel up orange tape and remove to access the top of rear camera motherboard clamp.
Flip up the black tab on the ZIF connector to detach the rear camera.
Step 23
- Remove rear camera from motherboard.
Remove rear camera from motherboard.
Step 24
- Separate the black plastic cover from the broken rear camera you removed.
- Glue black plastic cover onto the new replacement rear camera.
Separate the black plastic cover from the broken rear camera you removed.
Glue black plastic cover onto the new replacement rear camera.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Nathan Granger
Member since: 02/12/2018
202 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
USF Tampa, Team S15-G3, Boczar Spring 2018
Member of USF Tampa, Team S15-G3, Boczar Spring 2018
USFT-BOCZAR-S18S15G3
4 Members
12 Guides authored
