Difficulty

Moderate

Steps

19

Time Required

                          25 - 45 minutes            

Sections

5

  • Back Cover
  • 2 steps
  • Battery
  • 1 step
  • Motherboard Cover
  • 4 steps
  • Motherboard Assembly
  • 11 steps
  • Earpiece Speaker
  • 1 step

Flags

0

  • BackMotorola Moto C

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

You’ll need replacement adhesive to reattach components when reassembling the device.

What you need

Step 1

              Back Cover               
  • Power off your phone before beginning disassembly.
  • Insert a thumbnail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover.
  • Move it to the bottom left corner and pry the phone unit out of the back cover until you can get a good grip.

Power off your phone before beginning disassembly.

Insert a thumbnail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover.

Move it to the bottom left corner and pry the phone unit out of the back cover until you can get a good grip.

1024

Step 2

  • Lift the phone out of the back cover.

Lift the phone out of the back cover.

Step 3

              Battery               
  • Use a finger or spudger to lever the battery out of its recess and remove it.

Use a finger or spudger to lever the battery out of its recess and remove it.

Step 4

              Motherboard Cover               
  • Remove the six 3.5 mm long Torx T5 screws.

Remove the six 3.5 mm long Torx T5 screws.

Step 5

  • Insert an opening pick between the cover and the motherboard near the SIM 2 slot where the power buttons are located.
  • Slide and twist the opening pick to pry open the plastic clips securing the cover.

Insert an opening pick between the cover and the motherboard near the SIM 2 slot where the power buttons are located.

Slide and twist the opening pick to pry open the plastic clips securing the cover.

Step 6

  • Slide an opening pick between the cover and the motherboard on the opposite side next to the SD card slot.
  • Twist the opening pick to pry open the plastic clips securing the cover.

Slide an opening pick between the cover and the motherboard on the opposite side next to the SD card slot.

Twist the opening pick to pry open the plastic clips securing the cover.

Step 7

  • Remove the motherboard cover.

Remove the motherboard cover.

Step 8

              Motherboard Assembly               
  • Remove the three 2.5 mm long T5 Torx screws.

Remove the three 2.5 mm long T5 Torx screws.

Step 9

  • Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located on the bottom left of the motherboard.

Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located on the bottom left of the motherboard.

Step 10

  • Use a pair of tweezers to pull the power and volume button flex cable out of the ZIF connector.
  • Fold the power and volume button flex cable out of the way.

Use a pair of tweezers to pull the power and volume button flex cable out of the ZIF connector.

Fold the power and volume button flex cable out of the way.

Step 11

  • Use the flat end of a spudger to pry up and disconnect the display flex cable located at the bottom of the motherboard.

Use the flat end of a spudger to pry up and disconnect the display flex cable located at the bottom of the motherboard.

Step 12

  • Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located at the top of the motherboard next to the rear camera.

Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located at the top of the motherboard next to the rear camera.

Step 13

  • Use a pair of tweezers to pull the digitizer flex cable out of the ZIF connector.

Use a pair of tweezers to pull the digitizer flex cable out of the ZIF connector.

Step 14

  • Prepare an iOpener and apply it to the upper half of the display for at least two minutes to loosen the adhesive beneath the vibration motor and the rear facing camera.

Prepare an iOpener and apply it to the upper half of the display for at least two minutes to loosen the adhesive beneath the vibration motor and the rear facing camera.

Step 15

  • Don’t try to remove the motherboard all the way yet. The antenna cable is still connected to its rear side.
  • Use a spudger to carefully lift the motherboard until you can get a good grip. Avoid to damage the cables next to the motherboard.

Don’t try to remove the motherboard all the way yet. The antenna cable is still connected to its rear side.

Use a spudger to carefully lift the motherboard until you can get a good grip. Avoid to damage the cables next to the motherboard.

Step 16

  • Fold the motherboard over the battery cavity to access the coaxial cable connectors.

Fold the motherboard over the battery cavity to access the coaxial cable connectors.

Step 17

  • Use a pair of tweezers to pry up and disconnect the antenna cable from the back of the motherboard.

Use a pair of tweezers to pry up and disconnect the antenna cable from the back of the motherboard.

Step 18

  • Remove the motherboard.

Remove the motherboard.

Step 19

              Earpiece Speaker               
  • Remove the ear piece speaker.
  • When reassembling, be sure to properly orient the earpiece speaker such that the gold contacts are pointing away from the top edge.

Remove the ear piece speaker.

When reassembling, be sure to properly orient the earpiece speaker such that the gold contacts are pointing away from the top edge.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 

                    Tobias Isakeit                     

Member since: 03/31/2014

105,397 Reputation

                                      184 Guides authored                  



                       Badges:
                       46







                                                        +43 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored