Difficulty

Moderate

Steps

12

Time Required

                          25 - 45 minutes            

Sections

4

  • Back Cover
  • 2 steps
  • Battery
  • 1 step
  • Daughterboard Cover
  • 3 steps
  • Daughterboard
  • 6 steps

Flags

0

  • BackMotorola Moto C

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover               
  • Power off your phone before beginning disassembly.
  • Insert a thumbnail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover.
  • Move it to the bottom left corner and pry the phone unit out of the back cover until you can get a good grip.

Power off your phone before beginning disassembly.

Insert a thumbnail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover.

Move it to the bottom left corner and pry the phone unit out of the back cover until you can get a good grip.

1024

Step 2

  • Lift the phone out of the back cover.

Lift the phone out of the back cover.

Step 3

              Battery               
  • Use a finger or spudger to lever the battery out of its recess and remove it.

Use a finger or spudger to lever the battery out of its recess and remove it.

Step 4

              Daughterboard Cover               
  • Remove the four 3.5 mm long Torx T5 screws.
  • Some screws might be covered with stickers.

Remove the four 3.5 mm long Torx T5 screws.

Some screws might be covered with stickers.

Step 5

  • Apply the edge of an opening pick to the bottom right corner under the daughterboard cover.
  • Twist the opening pick to open the plastic clamps of the daughterboard cover.
  • Slide the opening pick to the left and pry it upwards until you can get a good grip on the daughterboard cover.

Apply the edge of an opening pick to the bottom right corner under the daughterboard cover.

Twist the opening pick to open the plastic clamps of the daughterboard cover.

Slide the opening pick to the left and pry it upwards until you can get a good grip on the daughterboard cover.

Step 6

  • Remove the daughterboard cover.

Remove the daughterboard cover.

Step 7

              Daughterboard               
  • Use a pair of tweezers to disconnect the antenna cable on the left of the daughterboard.

Use a pair of tweezers to disconnect the antenna cable on the left of the daughterboard.

Step 8

  • Use a spudger to disconnect the digitizer flex cable on the upper left of the daughterboard.

Use a spudger to disconnect the digitizer flex cable on the upper left of the daughterboard.

Step 9

  • Use a pair of tweezers to remove the rubber gasket that covers the microphone on the bottom right of the daughterboard.

Use a pair of tweezers to remove the rubber gasket that covers the microphone on the bottom right of the daughterboard.

Step 10

  • Prepare an iOpener and apply it to the bottom part of the display for at least two minutes to loosen the adhesive beneath the daughterboard.

Prepare an iOpener and apply it to the bottom part of the display for at least two minutes to loosen the adhesive beneath the daughterboard.

Step 11

  • Apply an opening pick to the bottom right corner of the daughterboard.
  • Carefully slide the opening pick under the daughterboard to cut the adhesive underneath.
  • Slide the opening pick from right to left to cut all the adhesive.

Apply an opening pick to the bottom right corner of the daughterboard.

Carefully slide the opening pick under the daughterboard to cut the adhesive underneath.

Slide the opening pick from right to left to cut all the adhesive.

Step 12

  • Twist the opening pick to lift the daughterboard until you can get a good grip.
  • Remove the daughterboard.

Twist the opening pick to lift the daughterboard until you can get a good grip.

Remove the daughterboard.

To reassemble your device, follow these instructions in reverse order.

Apply new adhesive where it’s necessary.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 

                    Dominik Schnabelrauch                     

Member since: 11/23/2016

158,135 Reputation

                                      649 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,769 Guides authored